Oracle Exadata Storage Server X6-2 High Capacity Скачать руководство пользователя страница 11

Страница: 11 / 70

Front Panel Status Indicators, Connectors, and Drives

Front Panel Status Indicators, Connectors, and Drives

This section describes the status indicators (LEDs), connectors, and drives on the front panel of

the Oracle Exadata Storage Server X6-2 High Capacity.

Front Panel With Twelve 3.5-inch Drives

The following figure shows the status indicators (LEDs), connectors, and drives on the front

panel of a Oracle Exadata Storage Server X6-2 High Capacity configured with twelve 3.5-inch

storage drives.

Figure

Legend

Description

Locator LED/Locator button: white

Service Action Required LED: amber

Power/OK LED: green

Power button

SP OK LED: green

6 - 17

Storage drive 0 (HDD) through storage drive 11 (HDD)

Top Fan Fault LED: amber; Power Supply (PS) Fault LED: amber; System Over Temperature Warning

LED: amber

Storage Server Features and Components

Содержание Exadata Storage Server X6-2 High Capacity







































































Результаты поиска

Содержание Exadata Storage Server X6-2 High Capacity

Отзывы:

Похожие инструкции для Exadata Storage Server X6-2 High Capacity

Бренды по названию

Популярные бренды

Oracle Exadata Storage Server X6-2 High Capacity, Руководство по установке

Результаты поиска

Содержание Exadata Storage Server X6-2 High Capacity

Отзывы:

Похожие инструкции для Exadata Storage Server X6-2 High Capacity

Бренды по названию

Популярные бренды