9
INSTRUCTION MANUAL
Juicer/Blender RK-0655
Please carefully read the instructions before using.
Diagram of name and position of main components
1. Pushing bar
2. Transparent cover
3. Juicing net
4. Middle ring
5. Handle
6. Residue barrel
7. Rotor
8. Main machine
Performances
1. Design is fine, simple, and beautiful, with combined
structure, easy to operate and clean.
2. High speed electric motor with overheating protection
is adopted, high efficiency, time saving, energy saving, high
service life of the motor.
3. Safety lock unit for switching is specially designed, in order
to make sure safety and reliability in use.
4. Design with anti-drip function juice mouth.
Attention before using
1. This machine is set with safety unit, when the handle does
not fasten the cover or the cutter seat is not fastened, the
motor cannot turn, so as to ensure safety for the user.
2. When disassembling or assembling the juicer, press the
upper of feed port of the cover with your hand, then force the
handle to slide in or out of cover slot.
3. When disassembling juicing net, first remove the cover and
residue barrel, then turn the middle ring up to 30 degrees
by holding juicing nozzle with your hand, and take up, the
juicing net will automatically leave the rotor.
4. In order to avoid damage, before using, first check power
supply for compliance with rated voltage.
5. Clean all parts able to disassemble (refer to the section of
“maintenance and cleaning”).
6. When assembling, please carefully read the diagram of
“name and position of main components”.
7. Please carefully read the “attentions” before using.
Juicing
1. Before using, please confirm the button switch of the main
machine in stop state, in this way, in case assembly is not
completed, starting the main machine can be avoided, so
unnecessary damage for persons or property avoided.
2. Before juicing, first confirm juicing net and rotor clutched
in position, and no hard contact between juicing net cutter
and transparent cover. Put the transparent cover on, put the
handle into the cover slot, then turn on the machine.
3. For using, assemble according to the diagram of “name
and position of main components”. Turn on power supply,
press switch to let the machine run no-load for 5 sec.
Put prepared vegetable or fruit into feed port of the juicer,
press with the pushing bar, evenly, hard and slowly, juice
of the vegetable or fruit can be found, original, fresh, good
for health.
4. For the juicer with large diameter, entire apple or pear can
be put in for juicing, no cutting apart needed, easy and
quick.
Note:
when pressing food with the pushing bar, force shall
be even or indirect, pressing force shall not be more than
1 kg, no too sudden force, otherwise, juicing effect will be
reduced.
5. Before using, please make sure to put the juice mouth to
drip position, and after turning off the machine, put the
juice mouth to anti-drip position to avoid juice come out
without juice cup and make the table dirty.
Operating time
This machine is designed with button switches of O grading,
I grading, II grading and inching (O for stop, I for weak
grading, II for strong grading, and for inching).
For juicing, select strong grading, for operating time, after
operating for 1min, stop for 1min, then use again. After the
above operation is performed for three times, stop for 15 min,
do not operate until the motor is cooled, in this way, service life
of this machine will be prolonged, the machine will serve you
more efficiently.
Attentions
1. This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without
supervision.
2. Keep the appliance and its cord aut of reach of children
less then 8 years.
3. Before using, put this machine on a stable and even table
board, operate according to the above methods.
4. Before juicing, first confirm juicing net and rotor clutched
in position, and no hard contact between juicing net cutter
and transparent cover. Put the transparent cover on, fasten
tight the handle, then turn on the machine.
5. Before being used, the motor works in running-in phase,
there may be slight peculiar smell and spark, this is
normal, after the motor works for some period, the above
phenomenon will disappear.
6. During juicing, make sure there is not too full juice and
residue in the middle seat and residue cup, if too full, please
cut off power supply, clean up, then use again.
UK
