Opticon OPL 7836 Скачать руководство пользователя | Manualshive

Страница: 38 / 40

background image

Opticon

OPL 7836

Specifications Manual

38

16. Regulatory Compliance

16.1. Laser Safety

The scanner emits laser beams.

JIS C6802: 2005: Laser class 2

IEC 825-1/EN 60825-1: Laser class 2

FDA CDRH Laser class II. Complies with 21 CFR 1040.10 and 1040.11 except for
deviations pursuant to laser notice No. 50 dated June 24, 2007.

Class II laser devices are not considered to be hazardous when used for their intended
purpose. Avoid staring into the laser beam.

16.2. Product Safety

EN60950-1: 2001

IEC60950-1: 2001

16.3. EMC

EN55022

EN55024

VCCI Class B: This is a Class B product, to be used in a domestic environment based on
the Technical Requirement of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used near a radio or television
receiver in a domestic environment, it may cause radio interference. Please install and
use the equipment according to the instruction manual.

FCC Part 15 Subpart B Class B: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

16.4. RoHS

RoHS: The restriction of the use of certain hazardous substances in electrical and
electronic equipment, 2002/95 EC.

«
...
36
37
38
39
40
»

Содержание OPL 7836









































Отзывы:

Нет отзывов

Похожие инструкции для OPL 7836

Бренд: Magtek Страницы: 2

DuraScan 700 Series

Бренд: Socket Страницы: 49

Бренд: Barkodes Страницы: 9

Бренд: TrekStor Страницы: 86

Бренд: Super-RFID Страницы: 6

Бренд: KoamTac Страницы: 7

Бренд: RIOTEC Страницы: 4

Бренд: Unitech Страницы: 65

Бренд: Star Micronics Страницы: 2

FlashLink STI-UCF100

Бренд: SimpleTech Страницы: 5

Бренд: TSC Страницы: 73

Floppy plus 7-in-1 Card Reader USB Powered Drive

Бренд: Iomega Страницы: 16

Бренд: Lbook Страницы: 41

Бренд: SICK Страницы: 166

Бренд: SICK Страницы: 188

Бренд: Pocketbook Страницы: 98

GA-2408T Series

Бренд: Gainscha Страницы: 93

Бренд: Zio Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды