Doc. ID 10110803
SFP Port Options
OSD Part
Number
SFP Description
OSDSFP100Fx
2 fiber SFP @ 1310nm
OSDSFP100WFxA
1 fiber SFP (Tx:1310nm, Rx:1550nm)
OSDSFP100WFxB
1 fiber SFP (Tx:1550nm, Rx:1310nm)
Port Allocation and LED indicators
Optical Port LED indicators
Fiber Link/Act
PoE
Function
Green
-
Link OK
Blinking
-
Link Activity
Red
-
No optical signal received
-
On
PoE On
Copper Port LED indicators
Link/Act
100Mb/s
(Amber)
Function
-
On
100Mb/s connection
-
Off
10Mb/s connection
On
-
Copper Link OK
Blinking
-
Copper Link Activity
Technical Specifications
Specification
Performance
Data Interface
IEEE 802.3 Ethernet
Data Rate
10/100Mbps
Operating Mode
Half or Full Duplex
Data Connector
2xRJ45. PoE on front panel, non-PoE
on rear panel
PoE
46 to 50V @ 0.4Amp Maximum
Operating Modes
Alternative A (Pins 1/2 and 3/6)
Alternative B (Pins 4/5 and 7/8)
Optical Interface
100Base-Fx
Optical Port
Connector
SFP - LC for 2-fiber, SC for 1 fiber
Transmitter Optical
Power
-15 to -8dBm into singlemode fiber
(see SFP datasheet for options)
Receiver Sensitivity
<-33dBm
Receiver Saturation
>-3dB
Standard SM Optical
Link Budget
>18dB:
>10km on multimode fiber @
1310nm
>40km on singlemode fiber
@ 1310nm
Power Requirements
+10V
DC
to +35V
DC
22V
AC
to 28V
AC
at 3VA plus up to an
extra 20VA for PoE operation (attached
powered device dependant)
Power Connector
3.5mm 2-way terminal block
Enclosure
Anodised elliptical metal case
Dimensions (mm)
52W x 55D x 26H
Weight of Module
300g
Operating
Temperature
-20 to 75
°
C, derated by 3
°
C/watt
supplied over the Ethernet cable.
Reduces to 30
°
C when connected to a
15W load
Relative Humidity
0 to 95% non-condensing
▲
ELECTROMAGNETIC COMPATIBILITY
WARNING
: This is a Class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take
adequate measures.
▲
OPTICAL OUTPUT OPERATION
WARNING
:
Laser Safety:
Class 1 Laser Product
per IEC/EN 60825-1:20011 standard.
Class 1
The OSD2052P is a
Class 1
laser product.
Precautions
▲
All service personnel should be provided training as
to the hazards of direct viewing of laser radiation
and of the precautionary measures during servicing
of equipment
▲
Areas where laser products are installed should be
restricted in access to trained service personnel
only and appropriate warning signs posted in the
work area.
▲
All laser apertures should be covered by protective
covers when not connected to optical fibers. Never
leave outputs uncovered.
▲
Laser equipment should be positioned above or
below eye level where possible. Apertures should
be positioned away from personnel
▲
Protective eyewear should be worn in the vicinity of
laser equipment
Warranty/Repairs
Thank you for purchasing equipment designed, manufactured
and serviced by Optical Systems Design (OSD). OSD warrants
that at the time of shipment, its products are free from defects in
material and workmanship and conforms to specifications.
For warranty period and repair service please contact your local
OSD distributor.
2
2
2
2
4
4
4
4
OPTICAL SYSTEMS DESIGN PTY LTD
7/1 Vuko Place, Warriewood 2102.
PO Box 891, Mona Vale,
NSW, Australia 1660.
Phone: +61 2 9913 8540
Fax: +61 2 9913 8735
1
1
1
1
3
3
3
3
Fiber Link/Act
100Mbps
Link/Act
1
1
1
1
2
2
2
2
3
3
3
3
PoE
Link/Act
Ethernet
Port 1/PoE
SFP Port
4
4
4
4
2
2
2
2
4
4
4
4
Fiber Link/Act
100Mbps
Ethernet
Port 2