manualshive.com logo in svg

Oppermann Regelgeräte CO2TRH, Руководство пользователя

Поделиться
Скачать
Oppermann Regelgeräte CO2TRH Скачать руководство пользователя страница 5

  

Sensors PG1  |  Data sheet No. 14110  |  Version 04-2017  | 

5

 | 

14

CO

2

-, temperature and humidity transducer CO2TRH

Display menu – operation

The following instructions only address the most important functions for illustration purposes.  

Modifications may be made without notice, in particular in connection with software updates.  

This documentation refers to software V 1.06.  

(The display starts shortly after connecting the power supply = Start).

The graphic display menu of the touch display is self-explanatory.  

There are 3 menu levels.

At the 

screen level,

the display can be switched on demand between collective display, individual display, 

and graphic tracking display,  and can also be used to enter the alarm thresholds. The enhanced display   

options are programmed at the 

screen level, 

and the transmitter parameters are programmed in the

settings level

.

 

Only the PIN2 = 4 x Zero = 0000 is stored in the default condition. This PIN controls access to the 

Settings parameter programming level

.If required, a PIN1 can be additionally assigned for access to  the 

Screen display level

.

It is possible to assign a different PIN1/PIN2 for access

.

Attention

:

these changed PINs must be stored in a safe place to ensure authorized access. 

Parameters cannot  be programed if PINs are not known or not entered. The device then needs  
to be sent to the factory

. 

Adjusting the desired display mode – display level

CO2/(

Temperature)/(relative humidity)

Start

1.06

Содержание CO2TRH















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды