background image

5

E115855#1

M

M

M

M

Wiring Diagram

15. Take a red and a black cable and cut a 

piece of 20 mm of each wire. Now re 

isolate the 4 ends and tin them. Connect 

the two cables crosswise to the external 

connections of the slide switch. (see 

diagram; the connections of the slide 

switch are the black rectangles; black 

cable: from left top to right bottom; 

right cable: from left bottom to right 

top) Take the red and black 200mm 

cable and cut them in half. Re isolate 

and tin the wire ends. Furthermore take 

one half of the red cable and connect 

it with the middle connection of the 

slide switch on the right side. After that 

take one half of the black cable and 

connect it with the middele connection 

of the slide switch on the left side. Put 

the two cables through the drilling 7d) 

and knot them together in the middle. 

See picture. Last but not least sold a flat 

receptacle (16) on each end.

red cable

black cable

16. Take one 100mm long red cable and cut it to 30mm. Re isolate and tin  the ends. Now connect one end with the 

front left inward facing connection of the slide switch. (In the wiring diagram it is the lowest black rectangle on 

the lright side.) Connect the other end to the left push button. (It looks like a seesaw on the diagram) After that 

connect one end of the remaining piece of the red cable (70mm) to the same slide switch connection. Connect 

the other end with the right push button.  

Moreover connect the two long red cables, coming from the engines, to the free connections of the push buttons 

and connect the two long black cables, coming from the engines, with the left sided outwards facing slide switch 

connection. (It is the lowest black rectangle on the left side) (See wiring diagram) Last put the batteries into the 

control box and connect it to the flat receptacles, red cable = + and black cable = -.

30mm red cable

70mm red cable

16

100mm 

red cable

100mm 

black cable

20mm red/black 

cable

Cabling of the control:

long red cable left sided motor

long red cable right sided motor

long black cable right 

sided motor

long black cable left 

sided motor

left 

sided 

motor

right 

sided 

motor

Содержание 115855










Отзывы: