Opex Perfect Pick Cortex Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 134

Opex Perfect Pick Cortex Скачать руководство пользователя страница 123

Troubleshooting

123

Perfect Pick® Cortex™ Operator Manual

OPEX Corporation

5.2.7. Last Zone Interruption

This happens with automated Workstations and conveyors where the OPEX
conveyor is excepting hand-off containers from a third-party conveyor were
extra containers do not receive the signaling to stop entering the OPEX
conveyor. The light tower is usually red or Blue/Red if a missed window is
present. This error usually means an integrated sensor exists, and needs to be
covered to keep other containers from entering the OPEX Conveyor while the
jam is being cleared (Figure 5-14).

Figure 5-14: Lost Zone Interruption

To clear the jam:

1.

After blocking the integrated sensor (if it is present), you must remove all
but one container from the last zone of the conveyor. Then pick up that last
conveyor with the zone is either clear or turns into a missed window.

2.

At that point you can place the container onto the workstation.

3.

Remove any missed windows were containers should exist.

4.

If done correctly, the conveyor should auto correct.

5.

Remove the cover for the integrated sensor.

6.

In some cases, you have to press the

Start

button on the workstation to

restart the conveyor.

«
...
121
122
123
124
125
...
»

Содержание Perfect Pick Cortex







































































































































Отзывы:

Нет отзывов