CONTENTS
SEALING THREADED
CONNECTIONS
To ensure a watertight seal, the cable
entry hole of the outdoor mounting kit
needs to be sealed with thread seal
tape to avoid water from entering the
camera.
Alarm I/O Connection
1
8
2
9
4
11
3
10
5
12
6
13
7
14
1
-
8
RS-485 D-
2
-
9
Alarm In 4
3
Alarm Out A1
10
Alarm In 3
4
Alarm Out A2
11
Alarm In 2
5
Alarm Out B1
12
Alarm In 1
6
Alarm Out B2
13
GND (Alarm &
RS-485)
7
RS-485 D+
14
-
Mount Lock
Screw
TIP:
Static IP is the recommended default.
Security Torx
Tool
POWER CONNECTION
1
AC24V L
2
GND
3
AC24V N
1
2
3
To power the camera, connect the
24vAC adaptor to the power connector
on the camera. Alternatively, users can
use PoE to power the camera if a PoE+
switch is available.
Threaded
Pendant
Alarm and RS-485
I/O Block
OE-C8213 IP
PTZ Camera
2-Pin Terminal
Power Block
3-Pin Terminal
Power Block
Threaded Mount
Adapter
ASSIGNING AN
IP ADDRESS
OpenEye IP cameras are set to DHCP
by default. If a DHCP server is not
detected after 4 minutes, the camera
will default to IP address 192.168.51.2.
If you are not using a DHCP server,
NCM will allow you to batch confi gure a
static IP address.
The IP address for the camera network
on your Apex recorder is 192.168.51.1.
Selecting multiple cameras and enter-
ing IP address 192.168.51.2 will set
an IP address on all selected cameras,
starting at 192.168.51.2 and increase
per camera.
1.
Open the Network Camera
Manager.
2.
Select applicable camera(s).
NOTE:
To change this IP address please refer
to your Apex recorder manual.
CONNECTING TO THE
IP CAMERA
To access the camera setup menu,
you need to open the Network Camera
Manager (NCM) utility. NCM is pre-
installed on all OpenEye Recorders,
and is also available for download on
the OpenEye website for installation on
your personal computer or laptop.
1.
Open
Network Camera Manager
.
2.
Locate your camera on the
Network Camera Manager
list.
3.
Input starting IP address, Subent
Mask, Gateway, DNS
.
4.
Apply changes.
5.
Wait 60 seconds before refreshing
NCM.
NOTE:
Refer to your Apex recorder manual
or quick start guide for instruction on
adding cameras. Passwords must
be 8-16 characters, contain at least 1
capital and 1 lower case letter, 1 number,
and 1 unique character.
NOTE:
OpenEye IP cameras ship
without a default password
.
DEFAULT USERNAME
AND PASSWORD
The admin user password can be set
using the following methods:
1.
OpenEye recorders running Apex
2.1 or newer will automatically set
a new unique password if:
•
Connected to an M-Series
recorder with a built in PoE
switch.
•
Connected to a network
switch through the
camera network port
and selected then added in
setup, if a new password has
not already been set.
2.
Connect to the camera directly
through a Web Browser and follow
the onscreen prompts.
3.
Use the Network Camera Manager
(NCM) Utility.
Username:
admin
NOTE:
The NCM software manual can be found
at
https://www.openeye.net/ncm-manual
POWER
This camera is compatible with 24vAC
and Power over Ethernet (PoE). Connect
power to the camera using the terminal
connector blocks.
CAUTION:
Risk of explosion of battery is replaced
by an incorrect type. Dispose of used batteries
according to the instructions.
