1.
Press the
(Standby/On) button to turn the unit on.
2. Press the FUNCTION button to 87.5(FM) or 520(AM) band.
3. Press the
or
button to tune in to a station.
•
Adjust the VOLUME control to obtain the desired volume.
Searching for a Station Automatically
•
Press and hold the
or
button until the tuner starts searching for a station, then release. After finding
a clear station, the search stops automatically.
Note: The search may not stop at a station with a very weak signal.
Presetting Stations
The unit can store a total of 20 stations in memory
(10 X FM, 10 X AM). Presetting allows you to tune in to a station directly.
1.
Tune in to a desired station (see previous section).
2. Press the MEMORY button. The preset number will blink on the display.
3. Press the PRESET button repeatedly to select the preset number you desire.
4. Press the MEMORY button again to store it in memory.
5. Repeat steps 1-4 to store other stations.
LIMITED WARRANTY
VENTURER ELECTRONICS (“VENTURER”
) makes the following limited warranty. This limited warranty extend
to the original consumer purchaser and is limited to non-commercial use of the product.
Ninety (90) Day Parts & Labor Warranty
VENTURER
products purchased in the United States are warranted to be free from defects in materials or
workmanship for a period of ninety (90) days from the date of their original retail purchase. If the unit fails to
conform to this warranty, we will service the product using new or refurbished parts and products, at
VENTURER’
s
sole discretion.
During a period of ninety (90) days from the effective warranty date,
VENTURER
will provide, when needed, service
labor to repair a manufacturing defect at its designated Service Center. To obtain warranty service in the Untied
States, you must first contact our
Customer Support Center at www.venturer.com
. The determination of service
will be made by
VENTURER
Customer Support.
PLEASE DO NOT RETURN YOUR UNIT TO VENTURER
WITHOUT PRIOR AUTHORIZATION
. New or remanufactured replacements for defective parts or products
will be used for repairs by
VENTURER
at its designated Service Center for ninety (90) days from the effective
warranty date. Such replacement parts or products are warranted for an additional ninety (90) days from the date
of repair or replacement. The Customer will be required to ship the unit to the Service Center indicated at the time
Customer Support is contacted to make the necessary repairs. The customer is responsible for all transportation
charges to the service facility.
Packaging and Shipping Instruction
When you send the product to the
VENTURER
service facility you must use the original carton box and packing
material or an equivalent as designated by
VENTURER
.
Your Responsibility
(1) You must retain the original sale receipt to provide proof of purchase.
(2) These warranties are effective only if the product is purchased and operated in the U.S.A. or Canada.
(3) Warranties extend only to defects in material or workmanship, and do not extend to any product or parts which
have been lost or discarded, or damage to product or parts caused by misuse, accident, improper operation
or maintenance, or use in violation of instructions provided with the product, or to product which has been
altered or modified without authorization of
VENTURER
, or to products or parts thereof which have had the
serial number removed or changed.
Out of Warranty
In the event your product requires repair after the limited warranty period has expired,
please contact our Customer Support Center at
www.venturer.com
Important:
You are responsible for any transportation, shipping or insurance relative
to the return of product to our Product Returns Center.
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular
purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any
warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties,
guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement
of any parts. In no event shall
VENTURER
be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these
warranties in any manner whatsoever. The time within action must be commenced to enforce any obligation of
VENTURER
arising under the warranty or under any statute, or law of the United States or any state thereof, is
hereby limited to ninety (90) days from the date of purchase. This limitation does not apply to implied warranties
arising under state law.
This warranty gives you specific legal rights and you may also have other rights, which may vary from state to state.
Some states do not allow limitations on how long an implied warranty lasts, when an action may be brought, or
the exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to you.
For more information on other products and services, please visit our web site at:
www.venturer.com
Important:
Also keep your “Bill of Sale” as proof of purchase.
Model no. ................................................. Product name ...................................................
Type of set ............................................................................................................................
Serial no. ................................................. Invoice no. ..........................................................
Date purchased........................................ Dealer name ......................................................
FOR SERVICE AND REPAIR, PLEASE VISIT
www.venturer.com
Design and specifications are subject to change without notice
.
As concerns grow about the environmental impact of outdated electronic
products, Venturer Electronics is committed to being a part of the solution.
Free of charge, Venturer Electronics customers can return qualifying units to us
for recycling. For more details, please visit our website at www.venturer.com/
recycle.
Printed in China
811-806091W010
CLOCK SETTING
LISTENING TO THE RADIO
1. Connect the adaptor to power the unit on.
(Setting the clock can only be done in STANDBY mode.)
2. Press the
button, the hour and minute digits blink.
3. Press the
HOUR button to adjust the hour digits.
4. Press the
MIN button to adjust the desired minutes then
press the
button once to confirm.
Note:
•
“PM” is displayed between 12 noon and midnight. 12:00 PM=Noon.
TIME DISPLAY INDICATOR
Hour Digits Minute Digits
or
FM/AM DISPLAY INDICATOR
Adjust Display Brightness
Press and hold the
SNOOZE button
to adjust the Display brightness once time .
BRIGHTNESS ADJUSTMENT
SLEEP TIMER SETTING
While listening to the radio, you can select the time interval in minutes before the unit turns off automatically.
1. Press
(
SLEEP
) to select among 90 MIN, 80 MIN, 70 MIN, 60 MIN, 50 MIN, 40 MIN, 30 MIN, 20 MIN, 10 MIN and OFF.
2. When sleep is activated, press and hold
(
SLEEP
) to view remaining sleep time. Press
(
SLEEP
)
again when the remaining sleep time is displayed to change the sleep time.
Note
: Sleep is automatically deactivated when the unit is turned off.
Note:
After setting alarm, you can press the
1/2
button to view the set alarm time. If
1/2
set to the same time, only
1
will alarm on.
To Change the Alarm Time
Just follow the instructions above to set the alarm time again.
To Turn Off Alarm
1. Snooze (If you want to snooze a few more minutes)
Press the
SNOOZE
button to mute the sound for 9 minutes. Snooze function continues to operate 59 minutes
after the preset alarm time.
2. To shut off alarm
Press the
(Standby/On)
button (alarm setting will stay active, it will turn on again, 24 hours later- the time
that the alarm is set to).
To Cancel Alarm Mode
In standby mode, press and hold the 1 (Alarm 1) or 2 (Alarm 2) buttons for 2 seconds until the ALM1 (alarm1) or
ALM2(alarm2) indicator disappears.
WAKE UP TO ALARM (BEEP OR RADIO)
To Set Alarm1
1. When in Standby mode, press the
1
button, the alarm indicator will light up.
2. Hold and press
1
button, the hour digit will flash, press
button repeatedly to adjust the hour.
3. Press
button repeatedly to adjust the minute.
4. Press the
Function button to select alarm mode : radio or beep.
For radio alarm, first tune in to a desired station and adjust the volume. The indicator beside radio will light up.
For beep alarm, just select it. The indicator beside buzz will light up, , and press
1
to confirm.
5. The alarm will wake up to “Radio” or “Beep” when alarm timer reaches the preset time and then shut off automatically
after 59 minutes.
Note:
the Alarm 2 setting is the same as Alarm 1.
Warning:
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• Be sure to install the battery before disconnecting the AC adapter.
• When the unit is left unplugged for a long time, remove the battery to avoid undue battery discharge and unit
damage from battery leakage.
• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
• Do not mix old and new batteries and Do not mix alkaline, standard (carbon-zinc) or rechargeable (Ni-MH, Ni-Cd,etc.)
batteries.
PLAYBACK VIA BLUETOOTH
®
ENABLED DEVICES
The unit can be paired and connected to the Bluetooth® enabled devices such as a smart phone.
Initial device pairing and connection
In order to pair and connect your Bluetooth® device for the first time:
1. Press the
(Standby/On)
to turn on the unit.
Press the Function button to Bluetooth® mode.
• The Bluetooth
® indicator light glows red and flashes
which means the unit is in Bluetooth®mode and ready to pair.
2. Turn on the Bluetooth® device you wish to pair and connect.
3. Press and hold the PAIR button on the unit. The Bluetooth® indicator light will start flashing rapidly which
means it is pairing.
4. On your Bluetooth® enabled device, search for the“ONB14AV204” in the list of discovered devices and select
it. It may take the unit and Bluetooth® enabled device a few seconds to pair.
5. When the Bluetooth® indicator glows a solid red, the unit and the Bluetooth® enabled device are now paired
and connected.
6. You can now enjoy audio from the unit.
• The unit can only be connected to one Bluetooth
® device at a time.
• If your Bluetooth device (e.g. Smart phone etc.)need the PIN code while pairing,
please enter 4-digit number: 0000.
Reconnecting a Bluetooth® enabled device
Bluetooth® enabled devices must be reconnected when the device has been turned off or the unit has been turned off.
1. Turn on the Bluetooth® device that has already been paired with the unit.
2. Press the Power button to turn on the unit. Press the Function button to Bluetooth® mode.
3. Depending on your Bluetooth® device, your device may automatically connect to the unit.
• If the device does not automatically connect to the unit, press and hold the
PAIR
button on the unit until
the Bluetooth® indicator light starts flashing rapidly, then search for the “ONB14AV204” in its list of your
Bluetooth® devices and select it.
4. Once the Bluetooth® indicator turns a solid red, the Bluetooth® enabled device is paired and connected.
Pair and connect with another new device
In order to pair the unit to a new device, you must first disconnect the currently paired and connected Bluetooth®
device from the unit.
1. On the currently paired and connected Bluetooth® device, select the “ONB14AV204” from the list of currently
paired and connected devices, and disconnect it. Please refer to your Bluetooth® enabled device User’s Guide for
direction on how to disconnect a device. Or turn off it.
2. Follow the Initial device pairing and connection instructions above.
BLUETOOTH
®
DISPLAY INDICATOR
TROUBLESHOOTING GUIDE
Problems
Solutions
RADIO
Poor FM reception
• Rotate the unit horizontally until orientation with best reception is found.
• Electrical interference in your home can cause poor reception. Move the unit away
from them (especially those with motors and transformers).
Poor AM reception
• Rotate the unit horizontally until orientation with best reception is found.
CLOCK
Clock does not show the
correct time.
• There has been an electrical power interruption.
Alarm does not come on
at the preset time.
To turn on the RADIO or BEEP alarm, check the following points:
• Is the current time correctly set on the time display? Check the PM indicator.
• Is the alarm time correctly set?
BLUETOOTH
®
Bluetooth
®
devices
doesn’t pair with this
unit.
• Make sure your Bluetooth
® device is working properly.
Make sure the source is Bluetooth® mode.
• Check your device’s manual for details on
Bluetooth® pairing and linking.
SPECIFICATION
Power source
AC 120V ~ 60Hz 19W
For the power backup function: AA x 2 batteries
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc.
EN-4
EN-5