Onkyo TX-NR585, Инструкция по эксплуатации

Страница: 89 / 128

89
Front Panel ≫ Rear Panel ≫ Remote ≫
Contents
≫
Connections
≫
Playback
≫
Setup
≫
• The unit of distance can be changed by pressing the MODE button on the remote
controller. When using the unit “feet”, the setting is available in increments of 0.1 ft from
0.1 ft to 30.0 ft. When using the unit “meter”, the setting is available in increments of 0.03
m from 0.03 m to 9.00 m.
„
4. Level Calibration
Adjust the volume level of each speaker.
Setting Item Default Value Setting Details
Front Left 0 dB Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Center 0 dB Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Front Right 0 dB Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Height Left 0 dB Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
• The setting cannot be changed if "Configuration"
- “Zone Speaker” is set to “Zone 2” and Zone 2
is on.
Height Right 0 dB Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
• The setting cannot be changed if "Configuration"
- “Zone Speaker” is set to “Zone 2” and Zone 2
is on.
Surround Right 0 dB Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Surr Back Right 0 dB Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
• The setting cannot be changed if "Configuration"
- “Zone Speaker” is set to “Zone 2” and Zone 2
is on.
Setting Item Default Value Setting Details
Surr Back Left 0 dB Select a value between “-12 dB” and “+12 dB”
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
• The setting cannot be changed if "Configuration"
- “Zone Speaker” is set to “Zone 2” and Zone 2
is on.
Surround Left 0 dB Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Subwoofer 0 dB Select a value between "-15 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
„
5. Dolby Enabled Speaker
Change the settings of Dolby Enabled Speakers.
Setting Item Default Value Setting Details
Dolby Enabled
Speaker to Ceiling
6.0 ft/1.80 m Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between
"0.1 ft/0.03 m" and "15.0 ft/4.50 m" (0.1 ft/0.03 m
units).
• The unit of distance (ft/m) is displayed using the
unit selected for the "Distance” setting.
AccuReflex Off You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": When this function is not used
"On": When this function is used
• This setting can be selected when “Configuration” - “Height Speaker” is set to “Dolby
Speaker”.