TX-NR1010/3010/5010/ DTR-70.4
OPERATION CHECK-2
1.OPERATION CHECK(2/3)
1-8. CONFIRMATION OF HDMI MAIN OUTPUT OSD(ON SCREEN DISPLAY) OPERATION
a. Confirm that display SET-UP MENU for push SET UP buttons.
b. Confirm that specified operations for ENTER(with 4-cursor) buttons are made.
c. Confirm whether the screen displayed at the POWER ON is correct.
At the POWER ON, please confirm the following image is displayed on HDMI Main OUT.
ONKYO model (TX-NR1010/3010/5010)
Integra model (DTR-70.4)
1-9. MISCELLANEOUS
a. Confirm SELECTOR MUTING operation.
b. Check the action of Left, Right, Center, L-Sur., R-Sur., Subwoofer, Sur.Back-L,Sur.Back-R, Front High-L,Front High-R,
Level Up/Down.
c. Confirm analog, digital and video REC SELECTOR operation.
d. Confirm Video output signal as shown Table 2., while Video signal are input as shown Table 1.
e. Confirm the video signal from BD/DVD Composite in is output to HDMI monitor out at the initial setting.
Then, input video signal to Component IN1, confirm change to Component IN1 signal from composite video signal.
f. Confirm the firmware combination check.
1. Push STANDBY/ON button while pushing down TV/CD button to display "TEST-_".
2. Next, if Enter keys are pushed, FL display "F/W Set OK" or "F/W Set NG" after it becomes a F/W COMBINATION TEST MODE.
1-10. CONFIRMATION OF COOLING FAN OPERATION
See “OPERATION CHECK-4, -6” for TEST MODE operation.
a. When no input signal, confirm to fan no rotate.
b. When TEST4-43, confirm to fan slow speed rotate.
c. When TEST4-46, confirm to fan fast speed rotate.
1-11. CONFIRMATION OF HDMI AUDIO OPERATION.
See “OPERATION CHECK-4, -7” for TEST MODE operation.
CONFIRMATION OF HDMI I2S SIGNAL.
a. DVD-AUDIO Fs=192kHz 2ch signal is input from HDMI rerminal.
b. Change the state to "TEST 6-00,6-01,6-02,6-03 one by one. Confirm the signal is output from L/R,SW/C,SL/SR,SBL/SBR.
CONFIRMATION OF HDMI SPDIF SIGNAL.
c. When TEST 6-06, confirm the sound(HDMI IN3) outputs from the speaker.
d. When TEST 6-07, confirm the sound(DVD analog input) outputs from the TV of Main HDMI OUT and Sub HDMI OUT.
CONFIRMATION OF Zone2 HDMI SIGNAL.
e. When TEST 5-14, confirm the sound outputs of HDMI IN4 input from the Powered Zone2 speakers.
f. And confirm the HDMI video and audio output of HDMI IN4 input from the TV connected OUT Zone2 HDMI terminal.
1-12. COMFIRMATION OF NETWORK
See “OPERATION CHECK-4, -5” for TEST MODE operation.
a. PC and the set are connected through the router.
b. Connect Front USB memory to AVR USB port.
c. When TEST 3-09(Front), confirm this USB memory is shown in USB device list on the display of AVR.
d. Connect Rear USB memory to AVR USB port.
e. When TEST 3-10(Rear), confirm this USB memory is shown in USB device list on the display of AVR.
f. Confirm the audio signal is output, when TEST MODE is set from TEST 3-11 to TEST 3-18.
(Confirm at Zone2 Preout/Line out terminal.)
g. Confirm the figure of AVR's display increases, when TEST MODE is set from TEST 3-11 to TEST 3-17.
*Please wait for about 20 seconds after turning on the power supply of the set when you use from TEST 3-11 to TEST 3-18.
The following iPod models can be used for inspection.(The above-mentioned operation is not done excluding the following items. )
iPod classic, 3G nano, 4G nano, 5G nano