Onkyo TX-8150, Инструкция по эксплуатации

Страница: 36 / 52

Various settings
36
HeadphoneLevel: Set the volume level for when
headphones are used.
j 12 dB to i 12 dB (default setting: 0 dB)
∫ 3. Hardware
Speaker Impedance: If any of the connected speakers
have 4
h
or more to less than 6
h
impedance, or if you
have connected a different set of left and right speakers
to the SPEAKERS A/B terminals, set the impedance to
4
h
.
0
Reduce the volume to minimum before setting.
6
h
(default setting)
4
h
Auto Standby
:
The unit will automatically enter standby
mode if there is no operation for 20 minutes with no audio
signal input.
On (default setting)
Off
Network Standby: you can turn on the power of the unit
via network using an application such as Onkyo Remote.
On
Off
(default setting)
0
When “Network Standby” is used, the power
consumption increases even when the unit is on
standby. However, the increase in power consumption
is kept to a minimum by automatically entering the
HYBRID STANDBY mode, where only the essential
circuit is operating.
0
If it is not displayed, wait for a moment until the
network feature starts.
Bluetooth Wakeup: This function wakes up the unit on
standby by connecting a Bluetooth enabled device.
On
Off
(default setting)
0
Setting to “On” increases the power consumption even
when the unit is on standby. However, the increase in
power consumption is kept to a minimum by
automatically entering the HYBRID STANDBY mode,
where only the essential circuit is operating.
0
This setting is fixed to “Off” if “6. Bluetooth”-“Auto In
Change” (
> 37) is set to “Off”.
0
If it is not displayed, wait for a moment until the
network feature starts.
Opt1 In Wakeup: When an audio signal is input through
the OPTICAL1 terminal while this unit is in standby, this
feature automatically detects it.
Off (default setting)
On : This unit is turned on and outputs the audio.
0
When a cable is connected to the OPTICAL1 terminal
and this setting is enabled, power consumption
increases even when the unit is on standby, however,
the increase in power consumption is kept to a
minimum by automatically entering the HYBRID
STANDBY mode, where only essential circuits are
operating.
DAB Scan: This setting determines which DAB bands
are scanned by the Auto Tuning function. To start
scanning, select the item and press the ENTER button.
World Wide (default setting): Band III (5A - 13F)
UK : Band III (11B - 12D)
DAB DRC: With the DRC (Dynamic Range Control)
setting, you can reduce the dynamic range of DAB digital
radio so that you can still hear quiet parts even when
listening at low volume levels - ideal for listening to the
radio late at night when you don’t want to disturb anyone.
0 (default setting): DRC off
1 : Large reduction in dynamic range
1/2 : Small reduction in dynamic range
FM Search Lvl: You can choose to have only those FM
stations with strong reception selected when tuning into
stations automatically if tuning regularly stops on FM
stations with weak reception. Select “FM” as the input
source to make this setting.
Normal (default setting)
Strong : Select only stations with strong reception.
∫
4. Source
IntelliVolume: Even when the volume control is the same
on this unit, there may be differences in the volume
depending on the connected devices. Adjust this when
you want to alleviate this difference. To set, select each
input source.
j
12 dB to
i
12 dB (default setting: 0 dB)
Name Edit: Enter a simple name of up to 10 characters
in length for the input sources or preset DAB/FM stations.
To set, select each input source or select the preset
number of the registered station.
0
For information on how to input characters, see
“Inputting characters” (
> 35).
∫
5. Network
Make the network setting.
0
If it is not displayed, wait for a moment until the
network feature starts.
0
When LAN is configured with a DHCP, set “DHCP” to
“Enable” to configure the setting automatically.
(“Enable” is set by default) To assign fixed IP
addresses to each components, you must set “DHCP”
to “Disable” and assign an address to this unit in “IP
Address” as well as set information related to your
LAN, such as Subnet Mask and Gateway.
Wi-Fi: Connect the unit to network via wireless LAN
router.
On : Wireless LAN connection
Off (Wired) (default setting): Wired LAN connection
Wi-Fi Setup: You can configure wireless LAN settings by
pressing the ENTER button when “Start” is displayed. For
details, see “Wi-Fi
®
connection” ( > 14).
SSID: The SSID of the connected access point will be
displayed.
Signal: The signal strength of the connected access
point will be displayed.
Status: The status of the connected access point will be
displayed.
MAC Address: View this unit’s MAC address.
TX-8150_mst.book 36 ページ ２０１５年６月１５日 月曜日 午後２時２８分