Onkyo HT-R648, Инструкция по эксплуатации

Страница: 46 / 76

46
En
Audio Selector
■
Audio Selector
`
ARC :
The audio signal from your TV tuner can be sent
digitally to the
HDMI OUT of the AV receiver.
*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
`
HDMI :
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI ( HDMI
IN ) and digital audio inputs ( COAXIAL IN or
OPTICAL IN ) have been assigned, HDMI input is
automatically selected as a priority.
`
COAXIAL :
This can be selected when COAXIAL IN has been
assigned as an input source. If both coaxial and
HDMI inputs have been assigned, coaxial input is
automatically selected as a priority.
`
OPTICAL :
This can be selected when OPTICAL IN has been
assigned as an input source. If both optical and
HDMI inputs have been assigned, optical input is
automatically selected as a priority.
`
Analog :
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are both
digital and analog inputs.
Note
• The setting is stored individually for each input selector.
• This setting can be made only for the input source that is
assigned as HDMI IN , COAXIAL IN , or OPTICAL IN . If both
HDMI ( HDMI IN ) and digital audio inputs ( COAXIAL IN or
OPTICAL IN ) are assigned, HDMI input will be selected as a
priority by setting to “ ARC ” (
➔
page 48 ). To select the digital
audio input, see “Digital Audio (Digital Audio Input)”
(
➔
page 40 ).
*1 You can select “ ARC ” if you select the TV/CD input selector.
But you cannot select it if you’ve selected “ Off ” in the
“ Audio Return Ch ” setting (
➔
page 48 ).
Setting the Incoming Digital Signal (Fixed
Mode)
■
Fixed Mode
`
Off :
The format is detected automatically. If no digital
input signal is present, the corresponding analog
input is used instead.
`
PCM :
Only 2-channel PCM format input signals will be
heard. If the input signal is not PCM, the
PCM
indicator will flash and noise may occur.
`
DTS :
Only DTS (but not DTS-HD) format input signals
will be heard. If the input signal is not DTS, the
DTS
indicator will flash and there will be no sound.
When “ HDMI ”, “ COAXIAL ” or “ OPTICAL ” is
selected in the “ Audio Selector ” setting, you can then
specify the signal type in “ Fixed Mode ”.
Normally, the AV receiver detects the signal format
automatically. However, if you experience either of the
following issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS.
• If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
• If noise is produced when fast forwarding or reversing a
DTS CD, try setting the format to DTS.
Note
• The setting will be reset to “ Off ” when you change the setting in
“ Audio Selector ” (
➔
page 46 ).
Menu Hardware
OSD
■
Volume OSD
`
On
`
Off
You can select if you wish to display the volume level on-
screen, when it is adjusted.
Remote Control
■
Remote ID
`
1 , 2 , or 3
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differentiate
the AV receiver from other components, you can change
its remote ID from “
1 ”, to “ 2 ” or “ 3 ”.
Note
• If you do change the AV receiver’s remote ID, be sure to change
the remote controller to the same ID (see below), otherwise, you
won’t be able to control it with the remote controller.
Changing the remote controller’s ID
Hardware
1
While holding down
RECEIVER
, press and hold
down SETUP until the remote indicator lights
(about 3 seconds) (
➔
page 39
).
2
Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice.