3
STEP 4
ASSEMBLY INSTRUCTION (60-2018)
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 3
Align the seat plate (D) over the pre-drilled holes under the
seat cushion (B). (NOTE the position of the seat plate handle
to the seat cushion FRONT). Attach the seat plate (D) to the
seat cushion (B) using four M8*20mm
screws (I) as shown.
Tighten securely with the Allen wrench (M).
2
CONTENTS
EXTRA HARDWARE INCLUDED FOR YOUR CONVENIENCE. ITEMS ARE NOT SHOWN TO SCALE.
PART
DESCRIPTION
STOCK#
QTY.
A
Back Cushion
61-2018BC
1
B
Seat Cushion
61-2018SC
1
C
Back Bar
61-2018BB
1
D
Seat Plate
61-2018SP
1
E
Gas Lift (seat
post)
61-2018GL
1
F
Star Base
61-2018SB
1
G
Caster
61-2018CA
5
PARTS LIST
PART
DESCRIPTION
QTY.
I
M8*20mm Screw
4
J
M8*25mm Screw
3
K
M6*42mm Screw
2
L
Washer
3
M
Allen Wrench
1
EXTR A 1 of each screw
---
3
HARDWARE KIT
STOCK# 61-2018HA
44
ASSEMBLY AND FUNCTION INSTRUCTION (60-2018)
STEP 1
Insert the casters (G) into the legs of the star base (F). Insert the
gas lift (E) into the center hole of the star base (F).
STEP 2
Attach the back bar (C) to the back cushion (A) using two
M6*42mm
screws (K). Tighten securely with the Allen wrench (M).
REPLACEMENT PARTS
STEP 5
Turn the assembled chair frame upright. Position the center hole
of the seat plate (D) over the gas lift (E). Then carefully lower the
chair onto the gas lift.
While seated, lean forward, lifting your body weight from the
seat. R each underneath the right side of the chair and locate
the handle. Lift the handle up slowly to allow the chair to
rise to the desired height. To lower the seat height, lift the
handle slowly while seated.
TO ADJUST SEAT HEIGHT
R ight
Handle
TO ADJUST TILT TENSION
R ound tension
knob
While seated, reach underneath the right side of the chair
and locate the handle. Slide the handle all the way out towards
the right (away from the seat). When the handle is in this
position, leaning back will cause the chair to tilt backwards.
To lock the chair in the upright (vertical) position, sit in the
chair, and push the handle in to the left (towards center of
seat).
TO OPERATE TILT
R ight handle:
* Pull outward
to allow tilting
* Push inward to
lock the chair in
place.
E
F
G
K
A
C
I
D
B
J
L
B
C
A
E
D
IF YOU ARE MISSING ANY OF THE PARTS ABOVE, OR IF YOU HAVE A
DAMAGED PART, PLEASE VISIT WWW.COMFORTPRODUCTS.NET/SUP-
PORT AND REFERENCE THE MODEL # ON THE FRONT OF THIS
MANUAL. SIMPLY COMPLETE THE INFORMATION, INCLUDING THE
PART YOU NEED. THE PART WILL NORMALLY BE SHIPPED WITHIN 48
HOURS.
Place the seat cushion (B) on a flat, clean surface such as a
table. Position the assembled parts from step 2, the back bar (C)
and back cushion (A), onto the seat cushion as shown. Align the
three holes in the back bar with the holes in the seat cushion
and fasten using three M8*25mm
screws (J) with washers (L).
Tighten securely with the Allen wrench (M).
Reach under the front center of the chair and grasp the
round black tension knob. To loosen the tilt mechanism, turn
the knob clockwise. This lessens the effort required to recline
the back cushion of the chair. To tighten the tension knob,
rotate counter-clockwise. Rotate the knob until the desired
resistance is reached.
