2. Slide the GDK onto the screw, see
figure 6.
Figure 6
If your original transmitter has two or three
buttons and uses DIP switches, set the #1
LED in the GDK to the opposite position
on the first DIP switch of your original
transmitter. Set the remaining GDK LEDs
to the exact same position of your original
transmitter’s DIP switches. If your original
transmitter has two or three buttons but
does not have DIP switches inside the
original transmitter or if the original
transmitter is lost or broken, please use
the DIP switches located on the radio
receiver (near the head unit) or at the push
button located on the garage wall. The
radio receiver can be found on or near the
garage door opener motor head mounted
on your garage ceiling. The DIP switches
are usually located near the point where
the electrical enter the garage door opener
head or on the externally mounted radio
receiver. YOU DO NOT NEED TO
DISASSEMBLE THE GARAGE DOOR
HEAD OR RADIO RECEIVER TO
LOCATE THE DIP SWITCHES,
HOWEVER, YOU MAY HAVE TO
REMOVE THE PROTECTIVE COVER.
The GDK should be mounted to an outside
wall, close to your Garage Door. Mount
the GDK on a flat vertical surface with
enough room above the GDK to slide the
cover up. The location should be easily
reached by anyone who will use it, at least
five feet above the floor and clear of any
moving Garage Door parts. It is
recommended that you choose a location
that is not in direct sunlight. If you mount
the GDK in a location that is exposed to
direct sunlight, the LEDs will be difficult to
see. It is also recommended that you do
not mount the GDK onto a metal surface,
as this may reduce the range of the signal.
To mount the GDK:
1. Using one of the supplied 1”
screws, drive the screw into the
wall in your chosen location,
leaving 1/4” of the screw
protruding from the wall.
3.
4.
3.
4.
Remove the battery cover and
disconnect the battery. This will not
erase the passwords or security
codes already stored in the GDK’s
memory.
Drive the second 1” screw through
the hole at the rear of the battery
compartment.
Remove the battery cover and
disconnect the battery. This will not
erase the passwords or security
codes already stored in the GDK’s
memory.
Drive the second 1" screw through
the hole at the rear of the battery
compartment.
Figure 7
Insert Screw
NOTE: Make sure that the GDK is aligned
in an upright position before driving in the
second screw.
5. Re-attach the battery and slide
battery cover back into place.
After you have stored your garage door
opener(s) security codes in the memory
the GDK and you have mounted the unit
you are ready to use your GDK. To open
your garage door:
1.
P I N
Open the GDK’s cover or, if the
cover is already open, press
ENTER. Key in your PIN, then
press ENTER. The GDK will beep.
NOTE: If you enter an incorrect PIN the
times, the GDK will lock you out for on.
minute. After one minute, re-enter the
correct PIN to proceed with opening you
garage door.
Press DOOR1, DOOR2 or
DOOR3, depending on which door
you would like to open. The GDK
will send a signal to your garage
door opener for as long as the
DOOR1 , DOOR2 or DOOR3 key
is pressed. Once you release one
of the keys, the signal will stop.
Your garage door will open. Thirty
seconds after the last key press,
the GDK will power off.
NOTE: After selecting the door to be
operated by pressing DOOR1 , DOOR2 or
DOOR3, pressing any key other than EXIT
will open or close that specific garage
door.
If, after opening DOOR1, you
would then like to open DOOR2 or
DOOR3, press the EXIT key once
and then press DOOR2 or DOOR3
to open another door.
A
Do NOT allow children to play with
the transmitter or door opener, If
children must use the GDK, please
supply proper training first.
Keep people clear of the garage
door as it is opening and closing.
The garage door could cause
serious injury or death.
Use the GDK only when you are
sure that all possible obstructions
have been removed.