One Control Crocodile Tail Loop Скачать руководство пользователя

Страница: 8 / 9

FX LOOPS ON AMPLIFIERS

In Setup 4 we are utilising the FX loop in the amp by running

OUT-2 into the amp input, then returning the signal to the OC
10 via the FX loop send to IN 8, the signal is then run through

loops 8 and 9 and returned to the amp FX return via OUT9
(N.O)

In most cases the effects loop of an amplifier is used to run

Time based FX such as Delay, Echo and Reverb, and Modu-

lation FX such as Chorus, Flangers and Pitch Shifters.
Primarily this is done to avoid distorting or driving the sound

created by these pedals by the preamp of the amplifier where
all the drive and distortion is created in an amplifier, this is

achieved by running the FX loop after the preamp stage of
any amplifier thus bypassing the drive stage and unwanted

distortion.

KEY
All red lines are cables
taking signal into OC10

All green lines are cables
taking signal out of OC10

All purple lines are cables
taking signal out of OC10
and immediately back Into
OC10 (Links)

OC10 setup utilising BJF buffer Circuit, 4 loops from Loops

1 Thru 7 running to amplifier front input and Loops 8 and 9

running through amplifier FX loop with Midi control from OC10

SETUP 5

PAGE 1

From Amplifier

FX Send to

OC10 Loop IN 8

From OC10 Loop

OUT9 (N.O) to

Amplifier FX

Return

MIDI IN

KEY (Continued)
All Gold lines are cables
Taking Midi signal out of
OC10

Содержание Crocodile Tail Loop










Результаты поиска

Содержание Crocodile Tail Loop

Отзывы:

Похожие инструкции для Crocodile Tail Loop

Бренды по названию

Популярные бренды

One Control Crocodile Tail Loop, Настройка

Результаты поиска

Содержание Crocodile Tail Loop

Отзывы:

Похожие инструкции для Crocodile Tail Loop

Бренды по названию

Популярные бренды