On-Q lyriQ AU7394 Series Скачать руководство пользователя страница 6

Страница: 6 / 8

301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com

Page 6 of 8

INSTRUCTION/INSTALLATION SHEET
lyriQ™ Standard Keypad

IS-0391 REV. D

6. lyriQ™ Keypad Installer Settings Reference Guide

AU5009-xx

lyriQ Standard Keypad in Studio,

AU5010-xx

lyriQ High Performance Keypad in Studio,

AU7394-xx

lyriQ

Standard Keypad,

AU1000-xx

lyriQ High Performance Keypad

Setting

Function

Use Case

Enter Installer
Setting Mode

Puts keypad into installer setting mode so that keypad
can be customized to environment and customer
preferences.

To implement:

quickly press keys in the following

sequence: Mute, Volume Up, Volume Down, Volume
Down. Repeat.

Note: The sequence needs to be done twice.

To enter into installer settings so that keypads
can be personalized for the user and to their
environment.

Whole House:
Enable/Disable

Default

(src 1, vol. 1) The local keypad will respond

and be able to be controlled from other keypads on the
system that have engaged Whole House Mode.

Whole House Disable

(src 1 vol.2)

turns off the ability

of a keypad to be controlled by other keypads that
have engaged Whole House Mode. Will not respond to
audio interrupt. Will still be able to implement a Whole
House command from keypad.
Keypads connected to systems with the Integration
Module will not be controlled by Integration Module
communications.

Note

This is set on each keypad, not globally.

Default

is used for normal operation and

environments.

Whole House Disable

is typically used for

outdoor spaces, baby’s rooms, offices or other
areas that should not be disturbed.

Turn-On Volume

Default

(src 2, vol. 1) turn on volume is about 10% full

volume.

Turn-On Volume

Variable turn on volume

: (src 2, vol.

adjust to

desired level

) enables a standard turn on volume

to be selected from 0% - 50% of full volume.

Last

volume

: (src 2, vol. 5) turn on volume will

be set at the volume that the user left the keypad
at before it was turned off.

Default

is used for normal operation and

environments.

Turn-On Volume

allows installer to customize

the volume level to the homeowner’s
environment and preference.

Содержание lyriQ AU7394 Series









Результаты поиска

Содержание lyriQ AU7394 Series

Отзывы:

Бренды по названию

Популярные бренды

On-Q lyriQ AU7394 Series, Инструкция по установке

Результаты поиска

Содержание lyriQ AU7394 Series

Отзывы:

Бренды по названию

Популярные бренды