Omron ZW-7000 Series Скачать руководство пользователя страница 49

Страница: 49 / 336

Basic Operations for Displaying Measurement Results

ZW-8000/7000/5000
User's Manual

Ba
si

c con

figuratio

Starting Up Sysmac Studio Measurement Sensor Edition

3 Operation during RUN Mode p.95

Start up Sysmac Studio.

Create a new project for the ZW.

From Category, select [Measurement Sensor]

and from Device, select [ZW] to click the [Cre-

ate] button.

If you have a previously created project, click [Open Project] to select the project.

2-8 Saving a project p.93

Select the [Specify a sensor] radio button to

specify the IP address of the Sensor Con-

troller to be connected.

Click the [Confirm] button to confirm the infor-

mation of the Sensor Controller.

When connection with Sensor Controller is suc-

cessful, Sensor Controller information is dis-

played.

Click [OK] button, the Sensing monitor window

appears.

Sensing monitor pane p.90

When connecting online for the first time

p.205

By default, the Sensor Controller has an IP address of 192.168.250.50

For the basic operations of Sysmac Studio, refer to “Sysmac Studio Version 1 Operation Manual” (W504).

Note

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды