manualshive.com logo in svg

Omron ZW-7000 Series, Руководство пользователя

Поделиться
Скачать
Omron ZW-7000 Series Скачать руководство пользователя страница 207

Changing between Online and Offline

ZW-8000/7000/5000 
User's Manual

205

 6

 

Offl

ine Settings

When connecting online for the first time

• When connecting to a Sensor Controller online for the first time, the Calibration ROM data backup window 

appears. 

 

If the Calibration ROM is lost, or it fails, the backed-up data can be recovered to the Sensor Controller.

 

Please keep the backed-up Calibration ROM data.

 5-3 Recovering Calibration ROM data p.195.

• When the Sensor Controller is in Setup mode; FUNC mode, online connection is disabled. Should switch to the 

RUN mode.

Note

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды