manualshive.com logo in svg

Omron ZW-7000 Series, Руководство пользователя

Поделиться
Скачать
Omron ZW-7000 Series Скачать руководство пользователя страница 284

Troubleshooting

282

ZW-8000/7000/5000 

User's Manual

8-2 Troubleshooting

This section describes how to temporarily remedy hardware-related trouble. 

Check the items below before sending the hardware for repair.

Error type

Phenomenon

Cause

Countermeasure

Pages

Startup error

Device restarts during 
operation.

The power supply device is not 
connected correctly.

Check if the power supply device 
conforms to the power supply 
specifications.

p.7

The power supply capacity is 
insufficient.

[NO.ROM] is displayed on 
the main digital.

The Calibration ROM is not 
connected.

Connect the Calibration ROM.
If the Calibration ROM is lost, or it 
fails, perform the temporary solution 
indicated on p.195 and then contact 
your OMRON representative.

p.35

Sensor Head 
calibration error

Sensor Head calibration 
fails.

The connection between the 
Sensor Controller and the Sensor 
Head or the extension fiber cable is 
not normal.

Confirm that the Sensor Controller, 
Sensor Head, and extension fiber 
cable are connected correctly.

p.36

Foreign matter is adhering to the 
fiber cable end surface.

Clean the Sensor Controller, Sensor 
Head, and end surface of the 
extension fiber cable connector.

p.70

The extension fiber cable is not set 
properly.

Confirm that the set length of the 
extension fiber cable matches the 
length of the connected extension 
fiber cable.

p.273

The fiber cable is disconnected.

The Sensor Head and extension fiber 
cable need to be replaced or 
repaired. Please contact an OMRON 
branch or sales office.

−

Display error

The main display remains 
on “- - - - - -.”

TIMING input is not ON. 

Turn the TIMING input ON.

p.78

The trigger level is not 
appropriately set for self-trigger.

Set the self-trigger level to an 
appropriate value.

p.163
p.252

Refer to the section of "[DARK] is displayed on the main digital.".

−

The main display 
becomes “SYSERR.”

A system error has occurred.

Identify the cause of the error based 
on the error code displayed on the 
sub-display and take an appropriate 
action.

p.280

The sub-display displays 
"LCK.ERR".

The EdgeTracks teach has failed.

Make sure the measurement surface 
is present and execute teach again. 
When the measurement surface is 
present, the STABILITY indicator is lit 
during RUN mode.

p.235

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды