manualshive.com logo in svg

Omron ZW-7000 Series, Руководство пользователя

Поделиться
Скачать
Omron ZW-7000 Series Скачать руководство пользователя страница 282

Error Messages

280

ZW-8000/7000/5000 

User's Manual

8-1 Error Messages

Errors Common to All Communication States

These errors occur in common regardless of communication state. When these errors occur, the ALARM 

output of parallel I/O turns ON, and “SYSERR” and error code are displayed on the main and sub-displays, 

respectively. 

The acquired error number of EI command is showed in the number in parentheses. 

If an error code other than the one listed above is displayed, the displacement sensor may be broken. Please 

contact an OMRON branch or sales office.

*1:

As a provisional measure, the measurement can be resumed using the data of the previously read Calibration ROM.
<Operation method>
With error code NO.ROM displayed on the sub-display, hold down the Mode switching key, and then when [OK/CAN] is displayed, press 
the ZERO/SET key.
<Cautions>
- When using this method, always check the serial number of the previously read Calibration ROM in "controller information," then check 

that it matches the Sensor Head side serial number. Measurement will not be correct unless they match.

- When restarting the main unit, perform the same operations again.

 

This operation is disabled for a displacement sensor into which no Calibration ROM has ever been inserted and started up.

Error Code

Name

Description

Cause

Remedy

BRK.ROM
(02)

Linearity correction 
data error

The linearity correction 
data is corrupted.

Calibration ROM damage Check to make sure that the 

Calibration ROM is correctly 
inserted. If correctly inserted, the 
Calibration ROM or displacement 
sensor may be broken.
Please contact an OMRON branch 
or sales office. (*1)

NO.ROM
(03)

Linearity correction 
data read error

Reading of the linearity 
correction data was not 
executed correctly.

Calibration ROM not 
inserted

BRK.SYS
(07)

System setting error

The system settings 
saved to the Sensor 
Controller are corrupt.

The displacement sensor 
power was turned OFF 
during saving/loading of 
system settings.

After holding down the Mode 
switching key, press the ZERO/SET 
key to clear the system settings and 
the bank data, and then resume the 
starting process.

BRK.BNK
(08)

Bank data error

The bank data saved to 
the Sensor Controller is 
corrupt.

The displacement sensor 
power was turned OFF 
during saving/loading of 
bank data.

BRK.TIM

（12）

Energization time 
error

The energization time 
data saved to the Sensor 
Controller is corrupt.

The energization time is 
corrupt due to a hardware 
malfunction.

After holding down the Mode 
switching key, press the ZERO/SET 
key to resume. (The energization 
time function becomes disabled.)

OVER.IP
(23)

IP address overlap 
error

The same address as that 
of the displacement 
sensor exists on the 
network.
Note: If a network hub is 
not used, this error may 
not appear.

The settings of IP 
addresses are invalid.

Change the IP address so that the 
IP address does not overlap with 
devices on the network.

MIS.IP
(25)

Ethernet 
communication 
parameter error

An invalid IP address is 
set.

Invalid IP address setting

Change to the correct IP address.

MIS.TYP
(60)

Type mismatch

The Sensor Head and 
Sensor Controller types 
do not match.

The Sensor Head and the 
Sensor Controller are not 
the correct pair. Both must 
be either the ZW-8000 
series or ZW-7000 series 
or ZW-5000 series.

Replace with the correct Calibration 
ROM. After replacing the Calibration 
ROM, turn ON themeasurement 
sensor power again.

MIS.SET
(61)

Set model mismatch

For the set model type, 
the Sensor Controller and 
Calibration ROM are not 
matched.

A Calibration ROM except 
ZW-7000 series is 
inserted.

Insert the Calibration ROM for ZW-
7000 series, and then retry to turn 
ON the Displacement Sensor.

MIS.BNK
(81)

Bank data error

The opened bank data is 
abnormal.

Occurs as a result of 
software downgrade.

To recover from the error, press and 
hold 

↑

 key or 

↓

key to clear the bank 

data.

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды