manualshive.com logo in svg

Omron V700-HMC71, Руководство по эксплуатации

Поделиться
Скачать
Omron V700-HMC71 Скачать руководство пользователя страница 20

(20/23)

(7)  NACK

When the User board was not able to receive a response correctly, NACK is
transmitted to demand that the response to be transmitted again. When the R/w
Module receives this command, the most recent response will be transmitted
again.

n

 Command

Command

Terminator

“1”

“2”

Cr

n

 Response

The most recent response will be transmitted again.

(8)  STOP

The STOP command is used to stop the R/W Module from executing a
command. When the R/W Module receives this command, it immediately stops
the execution of the current command and sets on stand by mode for a new
command.

n

 Command

Command

Terminator

“1”

“3”

Cr

n

 Response

Completion Code

Terminator

“0”

“0”

Cr

(9)  Oscillation ON / OFF

The Oscillation ON / OFF command specifies the oscillation of the antenna.

n

 Command

Oscillation ON 

Oscillation OFF

Command

Terminator

Command

Terminator

“1”

“4”

Cr

“1”

“5”

Cr

n

 Response

Completion Code

Terminator

“0”

“0”

Cr

Содержание V700-HMC71
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды