Omron V680 - 2, Руководство по эксплуатации продукта, Страница: 15 / 44

V680 Series
RFID System
15
Controller
Note: For details, refer to the User's Manual (Cat. No. Z249).
ID Controller Communications Specifications
ID Controller Input Specifications
(RST, TRG1, and TRG2) ID Controller Output Specifications
(RUN, BUSY/OUTS, ERROR/OUT4, OUT1,
and OUT2)
Note 1. When RST input is ON, the CPU halts operation and the RST
LED lights. The ERROR output is then reset.
2. Short-circuiting in a no-load condition may cause transistor
damage.
■
USB Port
The USB port is used for a simple connection with a personal computer using a USB cable. The port complies with USB 1.1, and the USB cable
uses a series A or series mini-B connector. A USB port driver must be separately provided. Consult with your OMRON representative for details.
When connected to a host device via USB, the communications will use 1:1 protocol regardless of the setting of DIP switches 3 to 9.
The USB port is not used for control purposes. When building a system, be sure to provide an RS-232C port or RS-422/RS-485C port.
Item Model V680-CA5D01-V2 V680-CA5D02-V2
Power supply voltage
Power consumption 24 VDC (
−
15% to +10%)
15 W max., 0.8 A max.
Ambient operating temperature
−
10 to 55
°
C (with no icing)
Ambient operating humidity 25% to 85% (with no condensation)
Ambient storage temperature
−
25 to 65
°
C (with no icing)
Ambient storage humidity 25% to 85% (with no condensation)
Insulation resistance 20 M
Ω
min. (at 500 VDC) applied as follows:
(1) Between power supply terminals and grounded case
(2) Between ground and terminals
Dielectric strength 1,000 VAC (50/60 Hz) for 1 minute
(1) Between power supply terminals and grounded case
(2) Between ground and terminals
Degree of protection Panel mounted (equivalent to IP20)
Vibration resistance
10 to 150 Hz variable vibration, 0.2-mm double amplitude at 15 m/s
2
acceleration, with 10
sweeps in X, Y, and Z directions for 8 minutes each
Shock resistance
150 m/s
2
Appearance 105
×
90
×
65 mm (not including projections)
Material Polycarbonate (PC) resin, ABS resin
Weight Approx. 300 g
Mounting method DIN Track or M4 screws
Connectable Amplifier Units 1 2
Item Specifications
RS-232C RS-422/RS-485
Connector specifications 9-pin D-Sub connector with threaded socket:
M2.6 5-pin connector mfd. by Phoenix Contact:
MC1.5/5GF-3.5
Transmission method Half-duplex serial 4-wire/2-wire half-duplex serial
Transmission speed 9,600/19,200/38,400/115,200 bps
Data length 7 or 8 bits
Stop bit length 1 or 2 bits
Error detection Parity (even/odd/none)
Cable length 15 m max. 500 m max.
Input voltage 24 VDC (+10% to
−
15%, including ripple)
(PNP and NPN compatible)
Input impedance 2.2 k
Ω
Input current 10 mA TYP (24 VDC)
ON voltage 19 V min.
OFF voltage 5 V max.
Input response 70 ms max.
Maximum
switching
capacity 24 VDC (+10% to
−
15%, including ripple)
100-mA photoMOS output (PNP and NPN
compatible)
Leakage current 100
µ
A max.
Residual voltage 2.0 V max.