607
Troubleshooting
Section 11-2
11-2-3 Fatal Errors
■
CPU Unit Indicators
There may be a CPU error or a fatal error if operation stops (i.e., the RUN indi-
cator turns OFF) and the ERR/ALM indicator lights. Error code for fatal errors
will be updated on the 7-segment display. If a CPU error occurs, the 7-seg-
ment display will remain unlit or the display will freeze.
Data on fatal errors is displayed on the Error Tab Page of the CX-Program-
mer’s PLC Error Window.
Take corrective actions after checking error details based on the 7-segment
display or the CX-Programmer display message together with the Auxiliary
Area Error Flags and error information.
Note
1.
Errors are listed in order with the most serious errors first.
2.
If two or more errors occur at the same time, the most serious error code
will be stored in A400.
3.
I/O memory will be cleared if a fatal error occurs (except those created with
FALS instructions).
4.
I/O memory will be held when the I/O Memory Hold Bit is ON, but outputs
will be turned OFF.
Memory Errors
POWER
Lit
RUN
Not lit
ERR/ALM
Lit
INH
---
BKUP
---
PRPHL
---
POWER
RUN
INH
PRPHL
BKUP
ERR/ALM
8.0.
→
f.1.
→
→
→
Memory error location
Seven-segment display
Probable cause and possible remedy
8.0.
→
f.1.
→ →
0.0.
→
0.1.
→
A checksum error has occurred in the user program.
Transfer the user program again.
→
0.0.
→
1.0.
→
A checksum error has occurred in the PLC Setup. Trans-
fer the PLC Setup again.
→
0.0.
→
8.0.
→
A checksum error has occurred in the routing tables.
Transfer the routing tables again.
→
0.1.
→
0.0.
→
A checksum error has occurred in the CPU Bus Unit
Setup. All settings for the CPU Bus Unit have returned to
the default setting. Perform the settings again.
→
0.1.
→
9.0.
→
A PLC Setup error, routing table setting error, and CPU
Bus Unit Setup error have occurred at the same time.
Take corrective actions for these three errors.
→
0.2.
→
0.0.
→
Automatic transfer from the Memory Cassette at startup
failed because the required data is not on the Memory
Cassette or the Memory Cassette is not installed.
Store the required data on the Memory Cassette and be
sure that the Memory Cassette is installed.
Содержание Sysmac CP1H
