Omron Sti F3SJ-A N Series, Быстрое руководство по установке

Страница: 13 / 23

12
F3SJ-A-TS
Quick Installation Manual
In other words, when a test rod is inserted into the detection zone, all 5 incident light level indicators turn
OFF, and the OFF output indicator turns ON. Use an appropriate test rod based on the type code for
inspection.
□
When muting function is used, installation condition of muting sensor must not be changed.
□
When muting function is used, muting status can be checked from where a worker operates or adjust the
machine.
□
Neither connector, cap, or bracket must be loose.
-Checking that Hazardous Parts Stop While the Machine Operates
□
The hazardous parts are movable when nothing is in the detection zone.
□
The hazardous parts stop immediately when a test rod is inserted into the detection zone at 3 positions:
"directly in front of the emitter", "directly in front of the receiver", and "between the emitter and receiver".
(Use the appropriate test rod.)
□
The hazardous parts remain stopped as long as the test rod is in the detection zone.
□
The hazardous parts stop when the power of the F3SJ is turned OFF while nothing is in the detection
zone.
-Items to Inspect Every 6 Months or When Machine Settings Are Changed
In addition to inspection item at operation start, following items must also be verified.
□
The outputs of the F3SJ-A-TS and the machine are properly wired.
□
The total number of times that the control relays/contactors have switched is significantly lower than their
design lives.
□
There is no disturbance light.
□
When F3SJ is connected again, a secondary sensor farthest from its power supply has either of the fol-
lowings:
• Cap
• Key cap for muting
• Muting lamp (set of lamp and cable)
□
Power supply's 0V must be grounded.
□
Wiring must not be bent, cracked, nor damaged.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product,
machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all
cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE
OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
Suitability for Use
In the interest of product improvement, specifications are subject to change without notice.
Regional Headquarters
OMRON EUROPE B.V. (Representative and Importer in EU)
Wegalaan 67-69, 2132 JD Hoofddorp
THE NETHERLANDS
Tel: (31)-2356-81-300 / FAX: (31)-2356-81-388
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011 / Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222 / Fax: (86) 21-5037-2200
OMRON Corporation
Industrial Automation Company (Manufacturer)
Contact: www.ia.omron.com
Shiokoji Horikawa, Shimogyo-ku, Kyoto, 600-8530 JAPAN
„
„
„
„
Suitability for Use
/Contact Information
Mounting/Beam Alignment Function Selection
Pre-Operation Checklist /
Maintenance Checklists