Omron STC-SBA503POE Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 59

background image

No.13S094-05

55/59

STC-SCA503POE / STC-SBA503POE

Product Specifications and User’s Guide

Name

Description

GevMCTT

Provides the transmission timeout value in miliseconds.

GevMCRC

Controls the number of retransmissions allowed when a message channel message
time out.

GevMCSP

This feature indicates the source port for the message channel.

GevStreamChanelSelector

Selects the stream channel to control.

GevSCPDirection

Reports the direction of the stream channel.

GevSCPInterfaceIndex

Index of network interface to use.

GevSCPHostPort

Controls the port of the selected channel to which a GVSP transmitter must send data
stream or the port from which a GVSP receiver may receive data stream.

GevSCPFireTestPacket

Sends a test packet.

GevSCPSDoNotFragment

The state of this feature is copied into the “do not fragment” bit of IP header of each
stream packet.

GevSCPSBigEndian

Endianess of multi-bytes pixel data for this stream.

GevSCPSPacketSize

Specifies the stream packet size, in bytes, to send on the selected channel for a GVSP
transmitter or specifies the maximum packet size supported by a GVSP receiver.

GevSCPD

Controls the delay (in timestamp counter unit) to insert between each packet for this
stream channel.

GevSCDA

Controls the destination IP address of the selected stream channel to which a GVSP
transmitter must send data stream or this destination IP address from which a GVSP
receiver may receive data stream.

GevSCSP

Indicates the source port of the stream channel.

UserSetControl

Name

Description

UserSetSelector

Selects the feature User Set to load, save or configure.

UserSetLoad

Loads the User Set specified by UserSetSelector to the device and makes it active.

UserSetSave

Save the User Set specified by UserSetSelector to the non-volatile memory of the
device.

UserSetDefaultSelector

Selects the feature User Set to load and make active by default when the device is
reset.

IPEngine

Name

Description

ProgrammableLogicController

Category that contains the Programmable Logic Controller (PLC) features.

For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com

Aegis

Electronic

Group,

Inc.

«
...
53
54
55
56
57
...
»

Содержание STC-SBA503POE




























































Отзывы:

Нет отзывов

Похожие инструкции для STC-SBA503POE

Бренд: Garmin Страницы: 19

MERCURY2 GigE Series

Бренд: Daheng Imaging Страницы: 184

Бренд: Edimax Страницы: 11

Бренд: Hama Страницы: 288

ZUIKO DIGITAL ED50mm f2.0 MACRO

Бренд: Olympus Страницы: 2

Бренд: DRALLE Страницы: 52

Бренд: FujiFilm Страницы: 60

Бренд: QHYCCD Страницы: 24

Бренд: TRASSIR Страницы: 2

Бренд: Q-See Страницы: 10

Бренд: Rollei Страницы: 46

Бренд: CHINON Страницы: 15

EX Z80 - EXILIM ZOOM Digital Camera

Бренд: Casio Страницы: 1

NIKKOR Z 14-24mm f/2.8 S

Бренд: Nikon Страницы: 4

Бренд: Grandstream Networks Страницы: 23

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды