Omron POWLI BU100XS страница 28 Скачать руководство пользователя

Страница: 28 / 49

4. Functions of the UPS

Goes
on

Goes
out

Goes on, blinks,
or goes out
depending
on the status.

< Display when the

equipment is at fault >

< Display when battery

replacement is required >

4-2 Testing the UPS (executing the self-diagnostic test)

You can use the following procedure to check whether replacing the battery inside the UPS is required and
whether the internal circuit is at fault.

• If the battery is not fully charged, the self-diagnostic test is not executed immediately.

After charging is complete, it is automatically executed.

(1) Connect your PC and other devices to the UPS and then press the Start Switch to start operation.

(2) Press and hold the Start Switch of the UPS for at least 10 second.

Release the start switch when a beep sounds. The Battery mode starts for testing purpose.

(3) After the 10-second test is complete, the normal operation automatically starts.

(4) If there is no error, the Error Lamp and the Battery Replacement Lamp do not go on and a beep does not

sound.

(5) If the Error Lamp goes on and a beep sounds, take necessary countermeasures according to "1" of "C.

Failure (display and beep when a failure occurs in equipment)" on page 23.

(6) If the Battery Replacement Lamp goes on and a beep sounds, immediate battery replacement is neces-

sary as it indicates extreme battery deterioration. Replace the battery according to "6-2 Replacing the
battery" on page 29.

* You can execute this test from the attached UPS monitoring software. For more information, refer

to the online help of the UPS monitoring software.

100%

75%

運転

テスト/
ブザー停止

容量表示

接続容量
オーバー

バッテリ
交換

異常

バイパス運転

電源出力

AC入力

バックアップ
運転

バッテリ
増設

INPUT

OUTPUT

停止

50%

25%

！

100%

75%

運転

テスト/
ブザー停止

容量表示

接続容量
オーバー

バッテリ
交換

異常

バイパス運転

電源出力

AC入力

バックアップ
運転

バッテリ
増設

INPUT

OUTPUT

停止

50%

25%

！

Содержание POWLI BU100XS


















































Результаты поиска

Содержание POWLI BU100XS

Отзывы:

Похожие инструкции для POWLI BU100XS

Бренды по названию

Популярные бренды

Omron POWLI BU100XS, Инструкция по эксплуатации

Результаты поиска

Содержание POWLI BU100XS

Отзывы:

Похожие инструкции для POWLI BU100XS

Бренды по названию

Популярные бренды