manualshive.com logo in svg

Omron NX1P2 series, Руководство пользователя по оборудованию

Поделиться
Скачать
Omron NX1P2 series Скачать руководство пользователя страница 137

4-3-5

Restrictions on Inrush Current for ON/OFF Operation

This section describes the restrictions on inrush current from the I/O power supply that occurs when
connected external devices turn ON and OFF.

Inrush Current Restrictions

If inrush current to the I/O power supply occurs when a connected external device turns ON or OFF,
do not allow the effective value of the I/O power supply current to exceed the following rated values
when the inrush current is added to the current consumption from the I/O power supply.
• Maximum I/O power supply current
• Current capacity of power supply terminals for the I/O power supply
Also, maintain the peak inrush current 20 A maximum and maintain the pulse width 1 s maximum.
Refer to 

4-4-3 Selecting Protective Devices

 on page 4-25 for the rated values of the items when the

CPU Rack is used.

Calculating the Effective Value of the I/O Power Supply Current

The formula to calculate the effective value of the I/O power supply current, Irms, is given below.

Irms=  Ip

2

 × D+Ia

2

 × (1-D)

(D=

τ

/T)

• Ip: Peak inrush current (A)
• Irms: Effective value of I/O power supply current (A)
• Ia: Total current consumption from the I/O power supply (A)
• D: Inrush current duty
•

t

: Inrush current pulse width (s)

• T: Inrush current period (s)

Ip

Ia  

Irms

τ 

T 

0A  

4 Designing the Power Supply System

4-21

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

4-3 Designing the I/O Power Supply System

4

4-3-5

 Restrictions on Inrush Current for ON/OFF Operation

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды