Omron NX-ECC201 Скачать руководство пользователя | Manualshive

Страница: 289 / 406

background image

13 - 11

13 Troubleshooting

NX-series EtherCAT Coupler Unit User’s Manual (W519)

13-
2 Che

cking

for Errors an

d T
ro

u

b

lesho

o

ti

ng wit

h

th
e Ind

icato

rs

13

13-
2-2 C

hecking for

E

rror
s an
d T
roubleshooting with the

Indicator

s on
the NX Unit

s



I/O PWR Indicator

The TS indicator on an NX Unit tells you the status and level of any errors in the NX Unit.

Refer to the manuals for the individual NX Units for details on the other indicators on the NX Units.

Color

Status

Meaning

Cause

Corrective action

Green

Lit

Power is currently sup-
plied from the I/O power
supply.

---

---- (This is the normal status.)

Not Lit

No power is currently sup-
plied.

There is no I/O
power supply.

Check the following items and make
sure that power is correctly supplied
from the I/O power supply.
Checks Related to the Power Supply
• Make sure that the power supply

cable is wired properly.

• Make sure that there are no breaks

in the power supply cable.

• Make sure that the power supply

voltage is within the specified
range.

• Make sure that the power supply

has enough capacity.

• Make sure that the power supply

has not failed.

13-2-2 Checking for Errors and Troubleshooting with the Indicators on

the NX Units

«
...
287
288
289
290
291
...
»

Содержание NX-ECC201























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX-ECC201

Бренд: NCR Страницы: 6

Бренд: Wave Italy Страницы: 16

Бренд: TA Hydronics Страницы: 14

Бренд: ZKTeco Страницы: 8

Бренд: EasyIO Страницы: 18

Бренд: Hama Страницы: 8

Бренд: Tech 21 Страницы: 2

Бренд: YASKAWA Страницы: 340

Бренд: Dejero Страницы: 24

Бренд: WINDY NATION Страницы: 16

Бренд: Kaba Mauer Страницы: 10

Бренд: Apex Toys Страницы: 7

767-4803/000-800

Бренд: WAGO Страницы: 80

Vertical Fan Coil

Бренд: Solaris Страницы: 10

Бренд: S&C Страницы: 24

Бренд: Procom Страницы: 10

Бренд: Belimo Страницы: 9

Бренд: Xantech Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды