3-12
Starting the Programming Console
3-12-1 Ports That Support the Programming Console Function
84
3-12 Starting the Programming Console
If the NS-series PT and CS/CJ-series PLC, are connected using a serial port, the
Programming Console function can be used on the Ladder Monitor without connecting a
Programming Console. (This function is not supported for CJ2 CPU Units.) All functions
except saving the ladder program to a cassette tape and restoring it can be executed.
Note
•
When using the Programming Console functions, carefully check that the system is
safe before performing the following actions.
- Changing monitored data
- Changing the operating mode
- Force setting/resetting bits
- Changing set values/present values
If unspecified persons may start the Ladder Monitor, use a password to prevent
incorrect operation. Refer to
3-14 Using a Password
for details on the password
function.
•
Confirm system safety before turning the power ON/OFF or resetting. Otherwise, the
system may operate unpredictably.
Note
•
The Programming Console function cannot be used when the PT is connected to a
CJ/CJ-series PLC using an Ethernet or Controller Link Board.
•
The CJ2 CPU Units do not support a Programming Console. The Programming
Console function cannot be used when connected to a CJ2 CPU Unit.
3-12-1 Ports That Support the Programming Console Function
To use the Programming Console function, the PT must be connected to a CS/CJ-series
PLC through either a peripheral port or RS-232C port on the CPU Unit of the PLC. If the
PT is connected to a CS/CJ-series PLC using a Serial Communications Board, a
Communications Unit, Ethernet, or Controller Link, the Programming Console function
will not operate. Only the Ladder Monitor functions can be used when connecting through
a Serial Communications Board or Communications Unit.
Serial Communications
Board
Communications Unit
Connect to
CPU Unit
CPU Unit
Peripheral
port
(RS-232C)
CPU
Unit
RS-232C
Port
CS1W-
SCB21
(RS-232C)
CS1W-
SCB41
(RS-232C/
RS-422)
CS1W-
SCU21
(RS-232C)
CJ1W-
SCU41
(RS-232C/
RS-422)
CJ1W-
SCU21
(RS-232C)
CS1G-CPU42/43/44/45-V1 Yes Yes No No No
CS1G-CPU42/43/44/45-H Yes
Yes
No No No
CS1H-CPU63/64/65/66/67-V1 Yes
Yes
No
No
No
CS1H-CPU63/64/65/66/67-H Yes Yes No
No
No
CS1D-CPU63/64/65/66/67-H Yes Yes No
No
No
CJ1G-CPU44/45 Yes
Yes
No
No
CJ1G-CPU42/43/44/45-H Yes
Yes
No No
CJ1H-CPU65/66/67-H Yes
Yes
No
No
CJ1H-CPU65/66/67-H-R Yes
Yes No
No
CJ1M-CPU12/13/22/23 Yes
Yes
No
No
Содержание ns series
