Omron M12 connector --- --- D4N-9E22 Скачать руководство пользователя страница 12

Страница: 12 / 35

D4N

1-conduit Models

Note:

Unless otherwise specified, a tolerance of

0.4 mm applies to all dimensions.

* Refer to following diagrams for details on M12 connectors.

Snap-action (1NC/1NO) (2NC), Slow-action (2NC) (3NC)

Slow-action (1NC/1NO) (2NC/1NO)

Model

Operating characteristics

D4N-

12H

D4N-

22H

D4N-

B2H

D4N-

D2H

D4N-

12G

D4N-

22G

D4N-

B2G

D4N-

D2G

Operating force

OF max.

4.5 N

Note:

Variation occurs in the simultaneity of contact
opening/closing operations of 2NC, 2NC/1NO, and
3NC contacts. Check contact operation.

*1. The operating characteristics of these Switches were

measured with the roller lever set at 32 mm.

*2. Only for snap-action models.
*3. Reference value.
*4. For safe use, always make sure that the minimum values

or greater are provided.

Release force

RF min.

0.4 N

Pretravel

to 27

Overtravel

OT min.

Movement differential

MD max. *2

Operating position

---

Total travel

TT *3

(80

)

Direct opening travel

DOT min. *4

Direct opening force

DOF min. *4

20 N

Model

Operating characteristics

D4N-

A2H

D4N-

C2H

D4N-

E2H

D4N-

F2H

D4N-

A2G

D4N-

C2G

D4N-

E2G

D4N-

F2G

Operating force

OF max.

4.5 N

*1. The operating characteristics of these Switches were

measured with the roller lever set at 32 mm.

*2. This PT value is possible when the NC contacts are open

(OFF).

*3. This PT value is possible when the NO contacts are

closed (ON).

*4. Only for MBB models.
*5. Reference value for MBB models only.
*6. Reference value.
*7. For safe use, always make sure that the minimum values

or greater are provided.

Release force

RF min.

0.4 N

Pretravel

PT *2

to 27

PT (2nd) *3

(44

)

PT *4

27.5

to 36.5

PT (2nd) *5

(18

)

Overtravel

OT min.

Operating position

---

Total travel

TT *6

(80

)

Direct opening travel

DOT min.

Direct opening force

DOF min. *7

20 N

Adjustable Roller Lever, Form Lock
(with Metal Lever, Resin Roller)
D4N-1

2G D4N-2

D4N-3

2G D4N-4

D4N-9

2G *

17.5 dia.

6.8

resin roller

Two, 4

+0.15

dia. holes

Depth: 5

2.15

0.05R

mounting holes

Conduit cap

20.5

27.5

0.2

21.5

0.2

31 max.

0.2

2.5

0.2

20 to 66R

0.1

14.2

39.5

(31)

Adjustable Roller Lever, Form Lock
(with Metal Lever, Rubber Roller)
D4N-1

2H D4N-2

D4N-3

2H D4N-4

D4N-9

2H *

50 dia.

rubber roller

Bearing

Stainless steel
lever

Two, 4

+0.15

dia. holes

Depth: 5

20.5

27.5

0.2

21.5

0.2

31 max.

0.2

2.5

0.2

0.1

14.2

48.2

41.3

(29.2)

32 to 66R

2.15

0.05R

mounting holes

Conduit cap

1-conduit M12 Connector
D4N-9

@@@

(14)

M12

14.2

http://www.ia.omron.com/

Содержание M12 connector --- --- D4N-9E22




































Результаты поиска

Содержание M12 connector --- --- D4N-9E22

Отзывы:

Похожие инструкции для M12 connector --- --- D4N-9E22

Бренды по названию

Популярные бренды

Omron M12 connector --- --- D4N-9E22, Руководство пользователя

Результаты поиска

Содержание M12 connector --- --- D4N-9E22

Отзывы:

Похожие инструкции для M12 connector --- --- D4N-9E22

Бренды по названию

Популярные бренды