background image

H7CZ

3

H7CZ Multifunction Preset Counter

Specifications

Ratings

*1.

Do not use the output from an inverter as the power supply.The ripple must be 20% maximum for DC power.

*2.

The display is lit only when the power is ON. Nothing is displayed when power is OFF.

Item

Models

H7CZ-L8

H7CZ-L8D1

Configuration

1-stage preset counter

Ratings

Power supply voltage 

*1

100 to 240 VAC, 50/60 Hz

24 VAC, 50/60 Hz or 12 to 24 VDC

Operating voltage fluctuation 
range

85% to 110% of rated supply voltage (12 to 24 VDC: 90% to 110%)

Power consumption

Approx. 9.4 VA at 100 to 240 VAC, Approx. 7.2 VA/4.7 W at 24 VAC/12 to 24 VDC

Mounting method

Flush mounting or surface mounting 

External connections

8-pin socket

Degree of protection

IEC IP66, UL508 Type 4X (indoors) for panel surface only and only when Y92S-29 Waterproof Packing is used. 

Input signals

Count, Reset

Counter

Maximum counting speed

30 Hz or 10 kHz (switchable) (ON/OFF ratio 1:1) 

Input mode

Increment, Decrement

Output mode

N, F, C, R, K-1, P, Q, and A.

One-shot output time

0.01 to 99.99 s

Reset system

External (minimum reset signal width: 1 ms or 20 ms, selectable), Manual, and Automatic reset (internal according 
to C, R, P, and Q mode operation)

Prescaling function

Yes (0.001 to 99.999)

Decimal point adjustment

Yes (rightmost 3 digits)

Sensor waiting time

290 ms max. (Control output is turned OFF and no input is accepted during sensor waiting time.)

Input method

No-voltage inputs:
ON impedance: 1 k

Ω

 max. (Leakage current: 12 mA at 0 

Ω

ON residual voltage: 3 V max. 
OFF impedance: 100 k

Ω

 min.

Control output

3 A at 250 VAC/30 VDC, resistive load (cos

φ

=1), Minimum applied load: 10 mA at 5 VDC (failure level: P, reference 

value)

Display 

*2

LCD 
Character height 
Count value: 10 mm
Set value: 6 mm

Digits

6 digits

99999 to 999999 

(

5 digits to +6 digits) 

Memory backup

EEPROM (overwrites: 100,000 times min.) that can store data for 10 years min.

Operating temperature range

10 to 55

°

C (

10 to 50

°

C if Counters are mounted side by side) (with no icing or condensation)

Storage temperature range

25 to 70

°

C (with no icing or condensation)

Operating humidity range

25% to 85%

Front panel color

Light gray (5Y7/1)

Содержание H7CX-R11D1





















Отзывы: