●Condition of the fitness of OMRON products
・
Please do not use this product to directly or indirectly use
to detect the human body for the purpose of ensuring the
safety. In the same application, please use the safety
sensor that is published on our sensor catalog.
・
Omron products are designed and manufactured as
general-purpose products for use in general industrial
applications. They are not intended to be used in the
following critical applications. If you are using Omron
products in the following applications, Omron shall not
provide any warranty for such Omron products, unless
otherwise specifically agreed or unless the specific
applications are intended by Omron.
(a) Applications with stringent safety requirements,
including but not limited to nuclear power control
equipment, combustion equipment, aerospace
equipment, railway equipment, elevator/lift
equipment, amusement park equipment, medical
equipment, safety devices and other applications
that could cause danger/harm to people s body
and life.
(b) Applications that require high reliability, including
but not limited to supply systems for gas, water and
electricity, etc., 24 hour continuous operating
systems, financial settlement systems and other
applications that handle rights and property.
(c) Applications under severe condition or in severe
environment, including but not limited to outdoor
equipment, equipment exposed to chemical
contamination, equipment exposed to
electromagnetic interference and equipment
exposed to vibration and shocks
(d) Applications under conditions and environment not
described in specifications
*1 In addition to the applications listed from (a) to (d)
above, Omron products (see definition) are not intended
for use in vehicles designed human transport (including
two wheel vehicles). Please do NOT use Omron products
for vehicles designed human transport. Please contact the
Omron sales staff for information on our automotive line of
products.
*2 The above is part of the Terms and Conditions
Agreement. Please use carefully read the contents of the
guarantee and disclaimers described in our latest version
of the catalog, data sheets and manuals.
●
Installation Environment
• Do not use the product in areas where flammable or
explosive gases are present.
• Install the product so that air can flow freely through its
cooling vents.
• Clean the ventilation holes and fan outlet regularly to
prevent dust and particles from clogging them. If they are
blocked, heat is trapped inside, causing a malfunction.
• Do not install the product close to high-voltage devices
and power devices in order to secure the safety of
operation and maintenance.
• Make sure to tighten all installation screws securely.
• When mounting the Sensor Controller using the DIN rail
mounting bracket, make sure the screw is tightened.
• Make sure to mount the product on DIN-rail securely.
●
Power Supply and Wiring
• Make sure to use the product with the power supply
voltage specified.
・
Do not connect AC power source to Sensor Controller. If
connects AC power source, it might be a cause of the
failure.
• The recommended power supply is the S8VS-
○○○
24
(manufactured by OMRON) or S8VK-G-
○○○
24
(manufactured by OMRON).
• Use the wire of a suitable size (AWG 16 to 12) according
to the current consumption.
• Keep the power supply wires as short as possible
(Max.2m).
• Use a DC power supply with safety measures against
high-voltage spikes(safety extra low-voltage circuits on
the secondary side).
• Do the following confirmations again before turning on
the power supply.
- Is the voltage and polarity of the power source set
correctly? (DC24V for positive terminal. DC0V for
negative terminal.)
- Make sure to connect the earth (FG) only to the
grounding terminal.
- Is not the load of the output signal short-circuited?
- Is the load current of the output signal appropriate?
- Is not the mistake found in wiring?
●Ground
• The power supply circuit of the FH-L series Sensor
Controller is not insulated from the internal circuit.
• When the connected camera to FH-L series Sensor
Control comes packaged with a base, make sure to
mount with the base. Since the exclosure of the camera
main body made of metals is short-circuited with the
internal circuit, the internal circuit might be short-circuited
with FG if no base is used, so that failures or malfunctions
may be caused.
• Perform Class D grounding (with a grounding resistance
of 100Ω or less).
• Keep the ground line as short as possible by setting the
grounding point as close as possible.
• Ground the FH-L series Sensor Controller independently.
If sharing the ground line with other devices or connecting
it with a building beam, the Sensor Controller might be
adversely effected.
• Check wiring again before turning on the FH-L series
Sensor Controller.
・
Do not ground the plus (+) terminal of the 24VDC power
source when the FH-L series Sensor Controller is
connected to the FH-MT12 with a USB cable.Doing so
may cause a short circuit of the internal circuit, resulting
in a malfunction.
・
Do not ground the plus (+) terminal when the FH-L series
Sensor Controller is connected to the
FH-SC12/FH-SM12.Doing so may cause a short circuit of
the internal circuit, resulting in a malfunction.
●
Other
• Use only the camera and cables designed specifically for
the product. Use of other products may result in
malfunction or damage of the product.
・
Please insert monitor connector perpendicularly so that
the connector resin part and pin are not rubbing against
each other. Damaged pin may cause contact failure due
to generation and invasion of resin powder.
• Always turn OFF the power of the FH-L series Sensor
Controller and peripheral devices before connecting or
disconnecting a camera or cable. Connecting the cable
with power supplied may result in damage of the camera
or peripheral devices.
• For the cable that is flexed repeatedly, use the robotic
cable type
(Bend resistant camera cable) to prevent damages.
• Do not apply torsion stress to the cable. It may damage
the cable.
• Secure the minimum bending radius of the cable.
Otherwise the cable may be damaged.
• Do not attempt to dismantle, repair, or modify the product.
• Should you notice any abnormalities, immediately stop
use, turn OFF the power supply, and contact your
OMRON representative.
• While the power is ON or immediately after the power is
turned OFF, the FH-L series Sensor Controller and
camera case are still hot. Do not touch the case.
• When disposing of the product, treat it as an industrial
waste.
• Do not drop the product nor apply excessive vibration or
shock to the product. Doing so may cause malfunction or
burning.
• This product is heavy. Be careful not to drop it while
handling.
• A lithium battery is incorporated, so a severe injury may
rarely occur due to ignition or explosion.
・
Be sure to take fail-safe measures externally when
controlling stages and robots by using the measurement
results of the Sensor Controller (axis movement output by
calibration and alignment measurement).
●
Regulations of KC marking
Ａ급 기기（업무용 방송통신기자재）
이 기기는 업무용(Ａ급) 전자파적합기기로서 판매자
또는 사용자는 이 점을 주의하시기 바라며,가정외의
지역에서 사용하는 것을 목적으로 합니다.
Image Processing System
●
Ambient Temperature
• For good ventilation, provide a clearance of 50 mm or
more above the sensor controller away from other
devices in the normal floor mounting. For the right and left
sides, provide a clearance of 30 mm or more, and for the
back side, 15 mm or more. These clearances are also
required when mounting multiple sensor controllers side
by side. For the back mounting, the back-side clearance
of 15 mm is nor required.
• Do not install the product immediately above significant
heat sources, such as heaters, transformers, or
large-capacity resistors.
• Do not let the ambient temperature exceed 55
℃
(127°F).
• Provide a forced-air fan cooling or air conditioning if the
ambient temperature is near 55
℃
(127°F) so that the
ambient temperature never exceeds 55
℃
(127°F).
●
Noise Resistance
• Do not install the product in a cabinet containing
high-voltage equipment.
• Do not install the Sensor Controller within 200 mm of
power cables.
●
Component Installation and Handling
• Touching Signal Lines
When touching a terminal part or a signal wire in a
connector, take anti-static measures using a wrist strap or
another device to prevent damage from static electricity.
• Handling a USB Memory Device/SD Memory Card
Before removing a USB memory device or SD memory
card, make sure that data is not being read or written to
them.
• For a USB memory device, the memory device's LED
flashes while data is being read or written. Make sure that
the LED stops flashing before removing the memory
device.
• Do not insert an SD card in the reverse orientation, at an
angle, or in a twisting manner.
• For an SD memory card, the SD BUSY LED of Sensor
Controller flashes while data is being read or written.
Make sure that the LED stops flashing before removing
the card.
• Turning OFF the Power
When a message is displayed indicating that a task is in
progress, do not turn OFF the power. Doing so causes
the data in the memory to be corrupted, resulting in the
product not operating properly upon the next start-up.
・
Do not turn OFF during saving data to Sensor
Controller.
Possible to be corrupted data and Sensor Controller may
not perform correctly at next startup.
・
When turns OFF, conform the followings proceedings
have completed. and then operate again.
-
When saves using Sensor Controller:
Confirm the save processing is completed and next
operation is possible.
-
When saves using communication command:
Intended command is completed.
BUSY signal is turned OFF.
・
Setting of Power Source
The power source need to be supplied from DC power
source apparatus which is taken a save ultra-low voltage
circuit: to protect high voltage.
●
Maintenance
• Turn OFF the power and ensure the safety before
maintenance.
• Clean the lens with a lens-cleaning cloth or air brush.
• Lightly wipe off dirt with a soft cloth.
• Dirt on the image element must be removed using an air
brush.
• Do not use thinners or benzene.
●
Communication with High-order Device
After confirming that this product is started up,
communicate with the high-order device. During start-up,
an indefinite signal may be output from the high-order
interface. To avoid this problem, clear the receiving
buffer of your device at initial operations.
●
Fail-Safe Measures
• When controlling stages and robots using the
measurement results from the FH-L series Sensor
Controller (axis movement output based on calibration
and alignment measurement), always take fail-safe
measures within the stage and robot systems, such as
checking whether the data obtained from the
measurement results is within the range of movement of
the stages and robots.
• On the FH-L series Sensor Controller side,
use logical operations and conditional branches in a
complementary way to add a check process based on
the range of movement of the stages and robots, for
example, "data is not externally output if in a range of
-XXXXX to XXXXX."
●
Connecting the Sensor Controller and Monitor with a
Switcher and Splitter
・
Do not use devices that make the sensor controller
recognize the monitor again when switching operation
is performed. Re-recognition process in switching
operation has an effect such as a delay in
measurement time.
INSTRUCTION SHEET
Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal.
TRACEABILITY INFORMATION:
Importer in EU
Omron Europe B.V.
Wegalaan 67-69
2132 JD Hoofddorp,
The Netherlands
Manufacturer
Omron Corporation,
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 JAPAN
2016
Meanings of Signal Words
Meanings of Alert Symbols
Alert statements in this Manual
The following alert symbols are used in this manual.
The following alert statements apply to the products in this
manual. Each alert statement also appears at the locations
needed in this manual to attract your attention.
Indicates a potentially hazardous
situation which, if not avoided, will
result in minor or moderate injury, or
may result in serious injury or death.
Additionally there may be significant
property damage.
WARNING
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury or in
property damage.
General Prohibition
Indicates general prohibitions, including
warnings, for which there is no specific symbol.
General Caution
Indicates general cautions ,including warnings,
for which there is no specific symbol.
Electrical Hazard
Indicates the possible danger of electric shock
under specific conditions.
Explosion Hazard
Indicates the possible danger of explosion under
specific conditions.
Laser Radiation Hazard
Indicates the possible danger of laser radiation or
light.
High Temperature Caution
Indicates the possible danger of injury by high
temperature under specific conditions.
CAUTION
●
Symbols and the meanings for safety precautions
described in this manual.
In order for the product to be used safely, the following
indications are used in this book to draw your attention to
the cautions. The cautions with the indications describe
the important contents for safety.
WARNING
CAUTION
This product must be used according to the
instruction manual. Failure to observe this may
result in impairment of functions and
performance of the product.
This product is not designed or rated for
ensuring safety of persons. Do not use it for
such purposes.
Never connect the AC power supply with this
product. When the AC power supply is
connected, it causes the electric shock and a fire.
Do not touch the terminals while the power supply
is ON. Doing so may result in electrical shock.
A lithium battery is built into the Sensor Controller
and may occasionally combust, explode, or burn if
not treated properly. Dispose of the Sensor Controller
as industrial waste, and never disassemble, apply
pressure that would deform, heat to 100
℃
or higher,
or incinerate the Sensor Controller.
Since camera that can be connected with this
product emits a visible light that may have an
adverse effect on the eyes, do not stare directly
into the light emitted from the LED. If a specular
object is used, take care not to allow reflected
light enter your eyes.
Please take external safety measures so that the
system as a whole should be on the safe side
even if a failure of a Sensor Controlle
r
or an error
due to an external factor occurred.An abnormal
operation may result in serious accident.
Please take fail-safe measures on your side in
preparation for an abnormal signal due to signal
conductor disconnection and/or momentary
power interruption.An abnormal operation may
result in a serious accident.
Danger of burns. Do not touch the case while the
LED is ON or just after power is turned OFF,
since it remains extremely hot.
Precautions for Correct Use
●
Installation and Storage Sites
Install and store the product in a location that meets the
following conditions:
• Surrounding temperature of 0 to 55
℃
(-25 to +70
℃
in
storage)
• No rapid changes in temperature (place where dew does
not form)
• Relative humidity of between 10 to 90 %
• No presence of corrosive or flammable gases
• Place free of dust, salts and iron particles
• Place free of vibration and shock
• Place out of direct sunlight
• Place where it will not come into contact with water, oils
or chemicals
• Place not affected by strong electro-magnetic waves.
• Place not near to high-voltage, or high-power equipment.
●
Orientation of Product
For good heat dissipation, install the product only in the
position shown below so as not to block the ventilation
holes.
FH-L550
FH-L550-10
Suitability for Use
Omron Companies shall not be responsible for conformity with any standards,
codes or regulations which apply to the combination of the Product in the
Buyer’s application or use of the Product. At Buyer’s request, Omron will
provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in
combination with the end product, machine, system, or other application or
use. Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
OMRON Corporation
Industrial Automation Company
Tokyo, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69,2132 JD
Hoofddorp The Netherlands
Tel: (31)2356-81-300
Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A
Tel: (1)847-843-7900
Fax: (1)847-843-7787
OMRON ASIA PACIFIC
PTE. LTD.
No. 438A Alexandra Road
#05-05/08 (Lobby 2), Alexandra
Technopark, Singapore 119967
Tel: (65)6835-3011
Fax: (65)6835-2711
OMRON (CHINA) CO.,LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai,
200120, China
Tel: (86)21-5037-2222
Fax: (86)21-5037-2200
Note: Specifications subject to change without notice.
OMRON
This product contains a lithium battery that
contains perchlorate, which is regulated by the
California state law.
Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
■
Regulations for Perchlorate in
California U.S.
Precautions for Safe Use
First, please check to see if the package has all the
necessary Sensor Controller parts.
■Confirm the Package
FH-L□□□-10 series
Sensor Controller: 1
FH-L□□□: 1
・Instruction Sheet (Japanese/English) : 1
・Installation Instruction Manual for FH-L series × 1
・General Compliance Information and Instructions for EU: 1
・Power source: 1 (male)
FH-XCN-L: 1
FH-L□□□-10 series
Sensor Controller: 1
FH-L□□□-10: 1
・Instruction Sheet (Japanese/English) : 1
・Installation Instruction Manual for FH-L series × 1
・General Compliance Information and Instructions for EU: 1
・Power source: 1 (male)
FH-XCN-L: 1
Vision System FH/FZ5 Series
User s Manual
Vision System FH/FZ5 Series
Hardware Setup Manual
Vision System FH/FZ5 series
Macro Customize Functions Programming Manual
Vision System FH/FZ5 series
Processing Item Function Reference Manual
Vision System FH/FZ5 series
User s Manual for Communications Settings
Model numbers
FH-L550
FH-L550-10
FH-L550
FH-L550-10
FH-L550
FH-L550-10
FH-L550
FH-L550-10
FH-L550
FH-L550-10
Man. No.
Z365
Z366
Z367
Z341
Z342
Refer to other related manuals.
■Relevant Manuals
Do not install the product in the following positions.
