![background image](http://html1.mh-extra.com/html/omron/f3sg-r-series/f3sg-r-series_user-manual_744006011.webp)
ix
F3SG-4RA-25-02TS
User’s Manual
Int
ro
ductio
n
E
Make sure to observe the following precautions that are necessary for ensuring safe use of the product.
Do not install, use, or store the F3SG-R in the following types of environments:
- Areas exposed to intense interference light, such as direct sunlight
- Areas with high humidity where condensation is likely to occur
- Areas where corrosive gases are present
- Areas exposed to vibration or shock levels higher than in the specification provisions
- Areas where the pollution degree is harsher than 3, such as outdoor environment
- Areas where the product may get wet with oil that can solve adhesive
- Areas where foreign material such as spatter adheres to the F3SG-R
• Loads must satisfy both of the following conditions:
- Not short-circuited
- Not used with a current that is higher than the rating
• Do not drop the product.
• Dispose of the product in accordance with the relevant rules and regulations of the country or area where the
product is used.
• Make sure that the F3SG-R is securely mounted and its cables and connectors are properly secured with the
torque recommended in this document.
• Do not apply excessive force (0.2 N
•
m or more) to the Rotary Switch when operating it. Doing so may
damage and make the Rotary Switch inoperable. Do not operate the Rotary Switch with tools that may
damage the product.
• Bending radii of cables must be equal to or higher than specified minimum values.
• When replacing the cable connectors with other types of connectors, use connectors that provide a
protection grade of IP54 or higher.
• Be sure to route the input/output lines for the F3SG-R separate from high-potential power lines or through an
exclusive conduit.
• To extend a cable length with a cable other than the dedicated cable, use a cable with the same or superior
specifictions.
4-5-3-6. Extending Cable Length with Commercially Available Cable
• Use the F39-JD
□
RA cables in environment where the product may be exposed to oil. Using the other
cables in such an environment may cause cutting oils or other substances to enter the cables, resulting in a
risk of damaging or burning the product.
• Interface Unit F39-GIF-1 is dedicated to F3SG-RA-02TS and F3SG-RR series. Do not use it for other F3SG-
RA series than F3SG-RA-02TS, F3SJ-A or F3SJ-E/B series.
• When powering on the F3SG-R with the Interface Unit being connected to the F3SG-R, the PC COM lines
must be open. Otherwise the F3SG-R goes to the Lockout state or does not send the safety outputs
(OSSDs).
• Read and understand this document for setting with the Rotary Switch and End Cap.
• The rated life of the LEDs used for this product is 6 years.
• Some cutting oils may affect the product. Before using cutting oils, make sure that the oils should not cause
deterioration or degradation of the product.
• Do not use the product with degraded protective structure such as swelling and crack in housing and/or
sealing components. Otherwise cutting oil or other substance may enter the product, resulting in a risk of
corruption or burning.
Precautions for Safe Use
Содержание F3SG-R Series
