Omron E5CC-T Скачать руководство пользователя

Страница: 42 / 186

2 CompoWay/F Communications Procedures

2 - 18



C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

(2) Response Code

•

Normal Completion

•

Error Occurred

(3) Operation Commands and Precautions

•

Communications Writing

Set the Communications Writing parameter to "ON: enabled" or "OFF: disabled" with the related

information setting. The setting can be accepted in both setup area 0 and setup area 1. An

operation error will occur, however, if enabling or disabling communications writing is set for an

event input.

•

RUN/RESET

Set the related information to select starting or stopping program operation. The setting can be

accepted in both setup area 0 and setup area 1.

•

AT Execute/Cancel

Set AT (auto-tuning) to “execute” or “cancel” with the related information setting. This command

can be accepted in setup area 0 only. An “operation error” will be generated in the following

instances:

•

When the RUN/RESET parameter is set to RESET (and the reset operation is set to stop

control).

•

During standby status (when the reset operation is set to stop control).

•

In manual mode or when executing from setup area 1.

•

When ON/OFF control is being used

•

When an attempt is made to execute another type of AT during AT execution

Example: When 40% AT is specified during 100% AT execution.

Hold

00: Clear hold
01: Hold

Advance

Response code

Name

Description

0000

Normal completion

No errors were found.

Response code

Error name

Description

1001

Command too long

The command is too long.

1002

Command too short

The command is too short.

1100

Parameter error

Command code and related
information are wrong.

2203

Operation error

•

The Communications Writing
parameter is set to "OFF"
(disabled). The command is
received regardless of the
Communications Writing
parameter setting (ON/OFF).

•

Processing could not be
performed. For details, refer to

(3) Operation Commands and
Precautions

below.

•

Non-volatile memory error

Command code

Command content

Related Information

Содержание E5CC-T



























































































































































































Результаты поиска

Содержание E5CC-T

Отзывы:

Похожие инструкции для E5CC-T

Бренды по названию

Популярные бренды

Omron E5CC-T, Руководство по связи

Результаты поиска

Содержание E5CC-T

Отзывы:

Похожие инструкции для E5CC-T

Бренды по названию

Популярные бренды