G-274
Safety Sensors / Components
1-conduit Models
Note: 1.
Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
2.
Variation occurs in the simultaneity of contact opening/closing operations of 2NC and 3NC contacts. Check contact operation.
3.
There are a minimum of five turns of the screw thread for a Pg13.5 conduit opening and four turns minimum for a G 1/2 conduit opening.
4.
Refer to page 273 for details on M12 connectors.
Note: 1.
Variation occurs in the simultaneity of contact opening/clos-
ing operations of 2NC, 2NC/1NO, and 3NC contacts. Check
contact operation.
2.
These PT values are possible when the NC contacts are
open (OFF).
3.
These PT values are nominal values possible when the NO
contacts are closed (ON). (1NC/1NO models only)
4.
Nominal value.
5.
Load and stroke values for the direct opening mechanism.
For safe use, always make sure that the minimum values or
greater are provided.
Plunger
D4N-1
@
31R D4N-2
@
31R
D4N-3
@
31R D4N-4
@
31R
D4N-9
@
31R (See note 4.)
Two, 4
+0.15
dia.
holes
Depth: 5
0
2.15
±
0.05R
mounting holes
Conduit cap
(See note 3.)
Blue
20.5
×
20.5
6 dia.
11
±
0.2
22
±
0.2
31 max.
55
47
±
0.2
2.5
OP
(27)
9
±
0.2
16.7
20
±
0.1
22
±
0.1
14 dia.
21.5
30
36
14.2
Roller Plunger
D4N-1
@
32R D4N-2
@
32R
D4N-3
@
32R D4N-4
@
32R
D4N-9
@
32R (See note 4.)
9.5 dia.
×
5
resin roller
Two, 4
+0.15
dia.
holes
Depth: 5
0
20.5
×
20.5
2.15
±
0.05R
mounting holes
Conduit cap
(See note 3.)
Blue
22
±
0.2
31 max.
55
47
±
0.2
2.5
OP 41
9
±
0.2
16.7
20
±
0.1
22
±
0.1
14 dia.
11
±
0.2
21.5
30
36
14.2
Two, 4
+0.15
dia.
holes
Depth: 5
0
One-way Roller Arm Lever
(Horizontal)
D4N-1
@
62R D4N-2
@
62R
D4N-3
@
62R D4N-4
@
62R
D4N-9
@
62R (See note 4.)
12 dia.
×
5
resin roller
2.15
±
0.05R
mounting holes
Conduit cap
(See note 3.)
Blue
11
±
0.2
21.5
30
36
14.2
10.2
14.8
22
±
0.2
31 max.
55
47
±
0.2
2.5
OP
9
±
0.2
16.7
20
±
0.1
22
±
0.1
14 dia.
11
±
0.2
35.5
±
0.2
20R
39.3
13.5
Operating
direction
Two, 4
+0.15
dia.
holes
Depth: 5
0
One-way Roller Arm Lever
(Vertical)
D4N-1
@
72R D4N-2
@
72R
D4N-3
@
72R D4N-4
@
72R
D4N-9
@
7R2 (See note 4.)
Operating
direction
12 dia.
×
5
resin roller
2.15
±
0.05R
mounting holes
Conduit cap
(See note 3.)
Blue
11
±
0.2
21.5
30
36
14.2
10.2
22
±
0.2
31 max.
55
47
±
0.2
35.5
±
0.2
2.5
9
±
0.2
14.7
20
±
0.1
22
±
0.1
14 dia.
11
±
0.2
R19
16.7
12
OP
Model
D4N-
@@
31R
D4N-
@@
32R
D4N-
@@
62R
D4N-
@@
72R
LF max.
10.8 N
10.8N
7.5 N
7.9 N
LT max.
4.5 mm
4.5 mm
7 mm
7 mm
PT 1
(See note 2.)
2 mm
2 mm
4 mm
4 mm
(PT 2)
(See note 3.)
(2.9 mm)
(2.9 mm)
(5.2 mm)
(4.3 mm)
OP
34
±
0.5 mm 44.4
±
0.8 mm
53
±
0.8 mm 27
±
0.8 mm
(TT)
(See note 4.)
(6 mm)
(6 mm)
(9 mm)
(9 mm)
DOF min.
(See note 5.)
20 N
20 N
20 N
20 N
DOT min.
(See note 5.)
3.2 mm
3.2 mm
5.8 mm
4.8 mm
F502-EN2-04.book Seite 274 Dienstag, 26. Juli 2005 5:48 17
