background image

SAFETY INFORMATION

To assure the correct use of the product, basic safety measures should always be 

followed including the warnings and cautions listed in this instruction manual.

OPERATING THE DEVICE

Contact your physician for specific information about your blood pressure. 

Self-diagnosis and treatment using measured results may be dangerous. Follow the 

instructions of your physician or licensed healthcare provider.
DO NOT adjust medication based on measurement results from this blood pressure 

monitor. Take medication as prescribed by your physician. Only a physician is 

qualified to diagnose and treat High Blood Pressure.
The monitor is not intended to be a diagnostic device.
If battery fluid should get in your eyes, immediately rinse with plenty of clean 

water. Contact a physician immediately.
If you have a condition that may compromise circulation, you may get an inaccurate 

reading with this device. Consult your physician before using this device.
Read all of the information in the instruction manual and any other literature in the 

box before operating the unit.
This device is intended for use in measuring blood pressure and pulse rate in the 

adult population. Do not use this device on infants or persons who cannot express 

their intentions.
Operate the device only as intended. Do not use the device for any other purpose.
Dispose of the device, components and optional accessories according to applicable 

local regulations. Unlawful disposal may cause environmental pollution.
Do not use a cellular phone near the device. It may result in an operational failure.
Use only Omron authorized parts and accessories. Parts and accessories not 

approved for use with the device may damage the unit.
Use only 1.5 V “AAA” alkaline batteries with this device. Do not use other types of 

batteries. This may damage the unit.

CARE AND MAINTENANCE

Do not subject the monitor to strong shocks, such as dropping the unit on the floor.
Do not submerge the device or any of the components in water.
Store the device and the components in a clean, safe location.
Changes or modification not approved by the manufacturer will void the user 

warranty. Do not disassemble or attempt to repair the unit or components.

SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL

WARNING

Indicates a potentially hazardous situation which, if not avoided, 

could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, 

may result in minor or moderate injury to the user or patient or 

damage to the equipment or other property.

BEFORE TAKING A MEASUREMENT

To ensure a reliable reading follow these recommendations:

1.  Avoid eating, drinking alcohol, smoking, exercising, and bathing for 30 minutes 

before taking a measurement. Rest for at least 15 minutes before taking the 

measurement.

2.  Stress raises blood pressure. Avoid taking measurements during stressful times.

3.  The cuff can be applied to your left or right wrist.

4.  Measurements should be taken in a quiet place.

5.  Position the unit at heart level throughout the measurement.

6.  Remain still and do not talk during the measurement.

7.  Wait 2-3 minutes between measurements. The wait time allows the arteries to return 

to the condition prior to taking the blood pressure measurement. You may need to 

increase the wait time depending on your individual physiological characteristics.

8.  Keep a record of your blood pressure and pulse readings for your physician. A 

single measurement does not provide an accurate indication of your true blood 

pressure. You need to take and record several readings over a period of time. Try to 

measure your blood pressure at the same time each day for consistency.

INTRODUCTION

Thank you for purchasing the OMRON® BP629 IntelliSense® Automatic Wrist Blood 

Pressure Monitor.

The monitor is compact and easy-to-use at home, at work, and during travel. Perfect for 

people who frequently monitor their own blood pressure.

Your new digital blood pressure monitor uses the oscillometric method of blood 

pressure measurement. This means the monitor detects your blood’s movement through 

your brachial artery and converts the movements into a digital reading. An 

oscillometric monitor does not need a stethoscope so the monitor is simple to use.

Clinical research has proven a direct relationship between blood pressure in the wrist 

and blood pressure in the arm. Changes in wrist blood pressure reflect changes in arm 

blood pressure because the arteries in the wrist and the arm are close to each other. 

Frequently measuring the blood pressure in your wrist will provide your physician with 

an accurate indication of changes in your blood pressure.

The BP629 comes with the following components:

• Monitor • Storage Case 

 

• 2 “AAA” Alkaline Batteries

• Instruction Manual printed in English and Spanish • Quick Start Guide

The BP629 IntelliSense® Automatic Wrist Blood Pressure Monitor is intended for 

home use.
       Please read this instruction manual thoroughly before using the unit.

 

Please keep for future reference. For specific information about your own blood 

pressure, CONSULT YOUR DOCTOR.

Fill in for future reference.

DATE PURCHASED: __________________

SERIAL NUMBER: ____________________

• Staple your purchase receipt here
• Register your product on-line at
  www.register-omron.com

SAVE THESE INSTRUCTIONS

INSTRUCTION MANUAL

Model 

BP629

5329416-7B

3 series

Automatic Wrist Blood 

Pressure Monitor

UNIT DISPLAY

DISPLAY SYMBOLS

IRREGULAR HEARTBEAT SYMBOL (       )

When the monitor detects an irregular rhythm two or more times during the 

measurement, the Irregular Heartbeat Symbol (       ) will appear on the display with the 

measurement values.
An irregular heartbeat rhythm is defined as a 

rhythm that varies by less than 25% from the 

average rhythm or 25% more than the average 

rhythm detected while the monitor is measuring 

the systolic and diastolic blood pressure.
If the irregular heartbeat symbol (        ) 

displays with your measurement results, 

we recommend you consult your 

physician. Follow the directions of your 

doctor.

MOVEMENT ERROR SYMBOL (       )

The Movement Error Symbol (        ) is displayed if you move your body during the 

measurement. Please remove the wrist cuff, and wait 2-3 minutes. Reapply the wrist 

cuff and take another measurement.

Internationally recognized guidelines for upper limit of 

normal home blood pressure readings are as follows: 

This is a general guideline because blood pressure depends on age and morbidity. A 

lower home blood pressure goal may be recommended for certain patients, 

including diabetic patients, pregnant women, and patients with renal failure.

Normal Heartbeat

Irregular Heartbeat

Short Long

Blood 

pressure

Pulse

Pulse

Blood 

pressure

Home Guideline for Upper Limit of Normal BP

Systolic Blood Pressure

135 mmHg

Diastolic Blood Pressure

85 mmHg

AAA

 Alkaline Batteries

Instruction 
Manual

KNOW YOUR UNIT

Main Unit:

Components:

Quick Start 
Guide

5.  Fold the remaining part of the wrist cuff back out of the 

way.

APPLYING THE CUFF ON THE RIGHT WRIST

When taking a measurement using the right wrist 

position the cuff as shown in the illustration.

SETTING THE DATE AND TIME

Set the monitor to the current date and time before taking a measurement for the first 

time. If the date and time has not been set, the measurement values are stored without 

any date or time information.

1.  TO START THE SETTING

Press the Date/Time Setting button (     ) to adjust the date 

and time.

The year flashes on the display.

2.  SETTING THE YEAR

Press the Date/Time Setting button (      ) to advance by 

increments of one year.

Press the Date/Time Setting button (     ) to set the current 

year.

The month flashes on the display.

NOTES:  

• 

The year can be set between 2010 and 

2040. When the display reaches 2040, it 

will return to 2010.

• 

Press and hold the (      ) button to 

increase the date and time values faster.

3.  SETTING THE MONTH

Press the Date/Time Setting button (      ) to advance by 

increments of one month.

Press the Date/Time Setting button (     ) to set the current 

month.

The day flashes on the display.

4.  SETTING THE DAY

Press the Date/Time Setting button (      ) to advance by 

increments of one day.

Press the Date/Time Setting button (     ) to set the current 

day.

The hour flashes on the display.

5.  SETTING THE HOUR

The time is set using AM or PM.

Press the Date/Time Setting button (      ) to advance by 

increments of one hour.

Press the Date/Time Setting button (     ) to set the current

hour.

The minute flashes on the display.

6.  SETTING THE MINUTE

Press the Date/Time Setting button (      ) to advance by 

increments of one minute.

Press the Date/Time Setting button (     ) to set the minute 

setting.

7.  TO TURN THE MONITOR OFF

Press the START/STOP button.

BATTERY REPLACEMENT

Low Battery Indicator

When the Low Battery Indicator appears on the display, turn the monitor off and 

remove all the batteries. Replace with 2 new batteries at the same time. Long-life 

alkaline batteries are recommended.

NOTES:  

 

Turn the unit off before replacing the batteries. If the batteries are removed 

while the unit is still on, the date and time will be reset to that of the 

previous use. The measurement results are not deleted.

• When the batteries are replaced, you may need to reset the date and time. If 

“-:--” appears on the display, refer to “Setting the Date and Time”.

• The batteries included with the device may have a shorter life.

CAUTION

Dispose of the device, components and optional accessories according to 

applicable local regulations. Unlawful disposal may cause environmental 

pollution.

WARNING

If battery fluid should get in your eyes, immediately rinse with

plenty of clean water. Contact a physician immediately.

TAKING A MEASUREMENT

1.  Sit comfortably in a chair with your feet flat on the floor.

 

2.  Hold your arm across your chest at heart level.

Hold your elbow firmly to avoid body movement.

Sit still and do not talk or move during the measurement.

3.  Press the START/STOP button.

All symbols appear on the display.

The cuff starts to inflate automatically.

As the cuff inflates, the monitor automatically determines your ideal inflation level. 

This monitor detects your blood pressure and pulse rate during inflation.

The Heartbeat Symbol (      ) flashes at every heartbeat.

Remain still and do not move until the entire measurement process is completed.

NOTE:

 To stop the inflation or measurement, push the START/STOP button. The 

monitor will stop inflating, start deflating, and will turn off.

4.  After the monitor has detected your blood pressure 

and pulse rate, the cuff automatically deflates. Your 

blood pressure and pulse rate are displayed.

 

5.  Press the START/STOP button to turn the monitor off.

NOTE:

 The monitor will automatically turn off after two minutes.

TROUBLESHOOTING TIPS

PROBLEM

No power.

No display appears on the unit.

Measurement values appear too 

high or too low.

CAUSES AND SOLUTIONS

Replace both batteries with new ones at the same 

time. Check the battery installation for proper 

placement of the battery polarities. 
Blood pressure varies constantly. Many factors 

including stress, time of day, how you wrap the 

cuff, may affect your blood pressure. 

Review the sections “Before Taking a 

Measurement” and “Taking a Measurement”.

CARE AND MAINTENANCE

To keep your digital blood pressure monitor in the best condition and protect the unit 

from damage, follow the directions listed below:
Do not forcefully

 bend the cuff. Do not fold tightly.

Clean the monitor with a soft dry cloth.

Do not use any abrasive or volatile cleaners.

Do not attempt to clean the cuff.

CAUTION

Do not submerge the device or any of the components in water. Do not subject 

the monitor to extreme hot or cold temperatures, humidity or direct sunlight.

CAUTION

Store the device and the components in a clean, safe location.

CAUTION

Do not subject the monitor to strong shocks, such as dropping the unit on the 

floor.

Remove the batteries

 if the unit will not be used for three months or longer. Always 

replace all the batteries with new ones at the same time.

Use the unit consistent with the instruction provided in this manual.

Use only authorized parts and accessories.

Use the unit in a manner consistent with the instructions provided in this manual.

CAUTION

Use only Omron authorized parts and accessories. Parts and accessories 

not approved for use with the device may damage the unit.

CAUTION

Changes or modification not approved by the manufacturer will void the user 

warranty. Do not disassemble or attempt to repair the unit or components.

ERROR INDICATORS

SYMBOL

CAUSE

Device error.

CORRECTION

Keep still and take another 

measurement.

Replace the batteries. 

Refer to “Battery Installation”.

Contact Customer Service.

Remove the monitor from your 

wrist. Wait 2-3 minutes and then 

take another measurement. Repeat 

the steps in section “Applying the 

Wrist Cuff.” If this symbol 

continues to appear, contact your 

doctor. 

Batteries are worn.

Irregular or weak

pulses are detected.

Movement during 

measurement.

Monitor could not 

detect pulse wave.

Cuff over-inflated.

Cuff under-inflated.

Cuff not applied 

correctly.

Take another measurement and 

remain still until the measurement 

is complete.

Remove the monitor from your 

wrist.

Read “Taking a Measurement”.

Wait 2-3 minutes.

Take another measurement.

LIMITED WARRANTY

Your BP629 IntelliSense® Automatic Wrist Blood Pressure Monitor, excluding the 

wrist cuff and batteries, is warranted to be free from defects in materials and 

workmanship appearing within 2 years from the date of purchase, when used in 

accordance with the instructions provided with the monitor. The above warranties 

extend only to the original retail purchaser.
We will, at our option, repair or replace without charge any monitor or wrist cuff 

covered by the above warranties. Repair or replacement is our only responsibility and 

your only remedy under the above warranties.
To obtain warranty service contact Customer Service by calling 

1-800-634-4350

 for the 

address of the repair location and the return shipping and handling fee.

Enclose the Proof of Purchase. Include a letter, with your name, address, phone 

number, and description of the specific problem. Pack the product carefully to prevent 

damage in transit. Because of possible loss in transit, we recommend insuring the 

product with return receipt requested.

THE FOREGOING IS THE SOLE WARRANTY PROVIDED BY OMRON IN 

CONNECTION WITH THIS PRODUCT, AND OMRON HEREBY DISCLAIMS 

ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING IMPLIED 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 

PURPOSE. IMPLIED WARRANTIES AND OTHER TERMS THAT MAY BE 

IMPOSED BY LAW, IF ANY, ARE LIMITED IN DURATION TO THE PERIOD 

OF THE ABOVE EXPRESS WARRANTY.

OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER 

SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT COSTS, 

EXPENSES OR DAMAGES.

This warranty provides you with specific legal rights, and you may have other rights 

that vary by jurisdiction. Because of special local requirements, some of the above 

limitations and exclusions may not apply to you.

FOR CUSTOMER SERVICE

Visit our web site at:                                                              www.omronhealthcare.com

Call toll free:                                                                                            1-800-634-4350

SPECIFICATIONS

Model:
Display:
Measurement Range:
Accuracy/Calibration:

Inflation:
Deflation:
Rapid Air Release:
Measurement Method:
Power Source:
Battery Life:
Operating Temperature 
/Humidity:
Storage Temperature 
/Humidity/Air Pressure:
Main Unit Weight:

Main Unit Dimensions:

Measurable 
circumference of wrist:
Memory:
Contents:

BP629 (HEM-6200-Z)

LCD Digital Display
Pressure: 0 to 299 mmHg, Pulse: 40 to 180/min.
Pressure: ±3mmHg or 2% of reading

Pulse: ±5% of reading
Automatic by electric pump
Automatic pressure release valve
Automatic exhaust valve
Oscillometric method
1.5V 2 “AAA” batteries
Approx. 300 uses with 2 new alkaline batteries
50ºF to 104ºF (10ºC to 40ºC) /15 to 90% RH

-4ºF to 140ºF (-20ºC to 60ºC) /10 to 95% RH

700-1060 hPa
Approximately 4 1/8 oz. (117g)

not including batteries
Approx. 2 3/4"(l) × 2 3/4"(w) × 1 5/8" (h)

(70 mm × 71 mm × 41 mm) (not including the wrist cuff)
Approximately 5 1/4" to 8 1/2" (13.5 to 21.5 cm)

Up to 60
Main Unit, Storage Case, 2 “AAA” Alkaline Batteries, 

Instruction Manual, and Quick Start Guide

NOTE: These specifications are subject to change without notice.

Manufactured for :

OMRON HEALTHCARE Co., Ltd.

Distributed by :

OMRON HEALTHCARE, INC.

1925 West Field Court

Lake Forest, IL 60045 U.S.A.

www.omronhealthcare.com

© 2012 OMRON HEALTHCARE, INC.

Made in China

Note:

POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only)

This product has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference 

in a residential installation. The product generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If the product does 

cause harmful interference to radio or television reception, which can be determined by 

turning the product on and off, the user is encouraged to try to correct the interference 

by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Connect the product into an outlet on a circuit different from that to which the 

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for Canada only)

This digital apparatus does not exceed the Class B limits for radio noise emissions 

from digital apparatus as set out in the interference-causing equipment standard entitled 

“Digital Apparatus”, ICES-003 of the Canadian Department of Communications.

Cet appareil numérique respecte les limites de bruits radioeléctriques applicables aux 

appareils numériques de Clase B prescrites dans la norme sur le materiel brouilleur: 

“Appareils Numériques”, ICES-003 édictée par le minister des communications.

Changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment.

FCC STATEMENT

TO DELETE ALL VALUES STORED IN THE MEMORY

You cannot partially delete values stored in the memory. All values will be deleted.

1.  Press the START/STOP button to turn the monitor on.

2.  While holding the MEM button, press the START/STOP button down for more than 

5 seconds until the display appears as it does in the following illustration.

3.  Press the START/STOP button to turn the monitor off.

NOTE:

 The monitor will automatically turn off after two minutes.

CAUTION

Use only 1.5V “AAA” alkaline batteries with this device.

1.  Press the hook on the bottom of the battery cover 

and lift the cover off in the direction of the arrow.

2.  Install 2 “AAA” size batteries so the + (positive) and - 

(negative) polarities match the polarities of the battery 

compartment as indicated.

3.  Set the date and time.

Refer to “Setting the Date and Time”.

4.  Replace the battery cover.

NOTE:

 Make sure that the battery cover is securely in 

position.

BATTERY INSTALLATION

INTRODUCTION

Thank you for purchasing the OMRON® BP629 IntelliSense® Automatic Wrist Blood 

Pressure Monitor .

The monitor is compact and easy-to-use at home, at work, and during travel. Perfect 

for people who frequently monitor their own blood pressure.

Your new digital blood pressure monitor uses the oscillometric method of blood 

pressure measurement. This means the monitor detects your blood’s movement 

through your brachial artery and converts the movements into a digital reading. An 

oscillometric monitor does not need a stethoscope so the monitor is simple to use.

Clinical research has proven a direct relationship between blood pressure in the wrist 

and blood pressure in the arm. Changes in wrist blood pressure reflect changes in arm 

blood pressure because the arteries in the wrist and the arm are close to each other. 

Frequently measuring the blood pressure in your wrist will provide your physician with 

an accurate indication of changes in your blood pressure.

The BP652 comes with the following components:

• Monitor • Standard Adult Arm Cuff 

 

• 2 “AAA” Alkaline Batteries

• Instruction Manual printed in English and Spanish • Quick Start Guide

The BP652 IntelliSense® Automatic Wrist Blood Pressure Monitor is intended for 

home use.

Fill in for future reference.

DATE PURCHASED: __________________

SERIAL NUMBER: ____________________

• Staple your purchase receipt here
• Register your product on-line at
  www.register-omron.com

INSTRUCTION MANUAL

Model 

BP629

5329416-7A

3 series

Automatic Wrist Blood 

Pressure Monitor

Wrist cuff

Display

Battery compartment

Memory (MEM) button
START/STOP button
Date/Time Setting (      ) button
Date/Time Setting (      ) button

Memory symbol
Average value symbol

Movement error symbol
Battery low symbol

Pulse display

Date/Time display

Deflation symbol

Irregular heartbeat symbol

Heartbeat symbol
(Flashes during measurement)

Blood pressure level indicator

Systolic blood pressure

Diastolic blood pressure

APPLYING THE WRIST CUFF

CAUTION

Read all of the information in the instruction manual and any other

literature in the box before operating the unit.

CAUTION

This device is intended for use in measuring blood pressure and

pulse rate in the adult population. Do not use this device on infants

or persons who cannot express their intentions.

APPLYING THE CUFF ON THE LEFT WRIST

1.  Roll up sleeve. Make sure your sleeve is not rolled up too 

tightly on your arm. This may constrict the flow of blood 

in your arm.

2.  Wrap the cuff directly against your skin.

Do not apply over clothing. Place the cuff over your left 

wrist with your left thumb facing upward.

3.  Position the cuff leaving a clearance of approximately 1/2 

to 1 inch between the cuff and the bottom of your palm.

4.  Hold the bottom part of the cuff and wrap it around the 

wrist so it fits comfortably and securely around your wrist.

NOTE:

 Make sure the wrist cuff does not cover the 

protruding part of the wrist bone on the outside of 

the wrist.

USING THE MEMORY FUNCTION

Every time you complete a measurement the monitor stores the blood pressure and 

pulse rate in the memory. The monitor automatically stores up to 60 sets of 

measurement values (blood pressure and pulse rate). When 60 sets of measurement 

values are stored, the oldest record is deleted to save the most recent values.

AVERAGING FUNCTION

The monitor calculates the average reading based on up to the three most recent sets of 

measurement values taken within 10 minutes of the most recent reading.

NOTE: 

If two sets of measurement values are stored in the memory for the 10 minute 

period, the average is based on the two sets of measurement values. If only 

one set of measurement values is stored, this is displayed as the average.

TO DISPLAY THE MEASUREMENT VALUES

1.  Press the MEM button to display the average reading based on the three most recent 

sets of measurement values taken within 10 minutes of the most recent reading. The 

Average Value Symbol (       ) appears on the display when the average reading is 

shown.

 2.  Press the MEM button to display the set of measurement values from the most 

recent to the oldest.

 

NOTES:  

 

Press the MEM button repeatedly to display the next values.

  

• Press and hold the MEM button to display the values faster.

     The date and time are alternately displayed with the measurement values.

 3.  Press the START/STOP button to turn the monitor off.

Alternating date/time 

display

WARNING

The monitor is not intended to be a diagnostic device.

WARNING

Contact your physician for specific information about your blood pressure. 

Self-diagnosis and treatment using measured results may be dangerous. 

Follow the instructions of your physician or licensed healthcare provider.

WARNING

DO NOT adjust medication based on measurement results from this blood 

pressure monitor. Take medication as prescribed by your physician. Only a 

physician is qualified to diagnose and treat High Blood Pressure.

Отзывы: