OmniCell ERB Скачать руководство пользователя страница 65

Страница: 65 / 112

External Return Bin Installation and Service Guide/

67-2038 Rev D

Installation Instructions

2-55

Installation on G4 Cabinets

Cabling for the One-, Two-, Three-Cell G4 Cabinets

When a One-, Two-, Three-cell is ordered with an ERB, the

ERB adapter cable

is attached to the E-

box before shipping. In such case, the only step required is to connect the

ERB PowerCom cable

the adapter cable on the back of the console.

If the ERB is ordered later, the cables must be installed as follows.

1. Insert a flat head screwdriver in the upper right cutout on the back of the left block-off plate of

the console assembly and rock it back and forth until the metal breaks away, leaving an
opening for the PowerCom cable.

Figure 2-134.

Opening a slot for the ERB cable

If mounting the ERB on the left side of the cabinet,

Figure 2-135

shows another possible

location to open for the PowerCom cable.

Figure 2-135.

Location of PowerCom slot for mounting ERB on left side of cabinet

2. With an assistant, pull the E-box all the way forward on the drawer slides, unlocking the

drawer slides to allow extra access.

Содержание ERB

















































































































Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды

OmniCell ERB, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды