I/O Module
Processor Module
Power Supply
Power Supply
I/O Module
Omneon MediaDeck Rear View
1. Connect reference video to one of the
Reference
connectors.
2. Connect a 75 Ohm BNC terminator to the other
Reference
connector to terminate it, or connect it to
the next device in line that requires reference video.
Note:
Termination must be applied to the last device in the loop.
3. If required, configure VITC lines using the SystemManager. For details, refer to “Changing Omneon
MediaDeck Clock Reference VITC Lines” in the
Omneon MediaDeck
TM
User’s Guide.
Reference video should
always
be connected to the Omneon MediaDeck. Failure to connect reference video
may result in errors.
Omneon MediaDeck Processor Module
Reference
Reference
75 Ohm
Termination
(or loop to
next device)
2
Reference
Video
1
Connect Reference Video
7
For complete instructions on rack mounting
the Omneon MediaDeck
TM
System, refer
to the
Omneon MediaDeck™ User’s Guide
and the instructions provided with the rack kit.
Warning
: Safe handling
of this system requires
TWO people.
Rack Mounting
1
The following diagrams describe the functionality of connectors for
each Omneon MediaDeck Module. For detailed connection
instructions, refer to the
Omneon MediaDeck™ User’s Guide
.
Your system configuration and specific audio/video requirements
may differ.
Connect Audio and Video I/O
8
BNC
Connector
Detail
5000 Series SD MPEG-2/DV MediaDeck Module (MDM-5001)
Channel A
1/2
3/4
Chan. A
RS-422
SDI Video Out
For service only
Channel A
1/2
3/4
Channel B
1/2
3/4
Channel C
1/2
3/4
LTC
IN
OUT
AES Audio In
AES Audio Out
SDI Video In
A/B
C
Chan. A
Chan. B
Chan. C
The SystemManager application, used to operate
and configure the Omneon MediaDeck,
comes pre-installed on the SystemManager Platform.
The software-only version of SystemManager
(NSM-2007SW) can be installed and run
on your own client PC.
To install either the SystemManager Platform
or the software-only version of SystemManager,
refer to the
Omneon SystemManager Release Notes
and
Omneon SystemManager Installation Guide
for instructions.
These guides can be downloaded from:
ftp.omneon.com/updates/omneon/current/SystemManager/
Refer to the
Omneon MediaDeck™ Read Me First
in your MediaDeck kit
for help with downloading the necessary files.
SystemManager Platform
or
Software-only version
(NSM-2007SW)
Connect to your Gigabit Ethernet Network
5
Your file transfer system may be any system you use for editing or network storage. The Omneon MediaDeck supports
file transfers using FTP, SAMBA, and AFP protocols.
4. Attach an Ethernet cable to the Ethernet switch, and then attach the other end to the LAN port on your file transfer
system.
5. Attach an Ethernet cable to the
File
port on the Omneon MediaDeck, and then attach the other end to an
open port on the Ethernet switch.
1. Align the bezel in front of the chassis so that the Omneon logo appears
in the top-left corner, and the metal corners of the bezel are level with
the rack ears of the chassis.
Note:
Use TWO hands to perform this procedure.
3. Hand-tighten the four captive
thumb screws to secure the
bezel in place.
2. Keeping the corners aligned, press the bezel
straight onto the chassis
so that the top and bottom edges
of the bezel slide over the top
and bottom edges of the chassis.
The LED connector inside the
bottom right-hand corner of
the bezel connects to
the LED card inside the chassis.
3
Install the Bezel
3
2
Install the SystemManager Platform
or Client PC
4
Note:
For the following connections, Omneon recommends that you use a CAT 5e or CAT 6 Ethernet cable.
Do not use a crossover cable or an adapter.
1. Ensure that an Ethernet switch with Gigabit uplink capability has been installed in your equipment rack.
2. Attach an Ethernet cable to the
NIC 1
port on the SystemManager Platform, or an open LAN port on your client
PC. Attach the other end of the Ethernet cable to the Ethernet switch.
Note:
Do
not
use the NIC 2 port on the SystemManager Platform unless you have configured SystemManager as a
client, or you are using the NSM-2003. Refer to the
Omneon SystemManager Installation Guide
for details.
3. Attach an Ethernet cable to the
Control
port on the Omneon MediaDeck, and then attach the other end to an open
port on the Ethernet switch.
The Omneon MediaDeck uses DHCP to obtain an IP address from SystemManager.
3
3. Using the slot guides in the enclosure to guide the drive,
insert the disk drive all the way into the drive bay until
the camming lever on the left side of the carrier stops it.
4. Push the lever closed to lock the drive into place.
5. Install the remaining disk drives.
4
No Drives in
Bottom Row
Front View
of System
Note:
Disk drives can be installed in any order.
Note:
Do not attempt to install disk drives
into the bottom row of the drive cage.
This space is intended for air flow only.
Important
: Check with your network administrator
before connecting to your Ethernet network.
Connect to an Automation System (Optional)
6
Sample Automation System Connections
2
1. Unpack a disk drive.
2. Open the latch
on the front of
the disk drive by pressing
the tab to the right while
pulling the lever back, as shown.
Install the Disk Drives
2
Caution
: Electrostatic discharge can damage components.
Observe normal ESD [Electrostatic Discharge] procedures
when handling hard drive assemblies.
Note
: All DB-9 Male to
Male extension cables
in these diagrams are
customer supplied.
The RJ-45 to DB-9 cables
are supplied by Omneon.
Refer to the User’s Guide
for pinout information.
5000 Series SD MPEG-2/DV MediaDeck Module (MDM-5001)
Record Play
RS-422
Port A
RS-422
Port B
RJ-45 Male
to DB-9
Female
DB-9 Male
to Male
Record
Play
Automation System
5320 Series HD/SD MPEG-2 Dual I/O MediaDeck Module (MDM-5321)
5220 Series SD MPEG-2 Dual I/O MediaDeck Module (MDM-5221)
DB-9 Male
to Male
VTR
PVW
Record
Play
422
(3)
422
(4)
422
(1)
422
(2)
RJ-45 Male to
DB-9 Female
Record
Play
RJ-45 Male to
DB-9 Female Splitter
RS-422
Port A/B
RS-422
Port C
Automation System
Rear Panel
5320 Series HD/SD MPEG-2 Dual I/O MediaDeck Module (MDM-5321)
5220 Series SD MPEG-2 Dual I/O MediaDeck Module (MDM-5221)
AES Out
Channel B
3/4
Channel A
1/2
3/4
Chan. A
RS-422
Channel A
1/2
3/4
1/2
3/4
LTC
IN
OUT
AES Audio In
AES Out/Thru
A
Chan. A
For service only
HD or SD SDI Video In
HD or SD SDI Video Out
HD or SD SDI Video Out/Thru
3/4
1/2
Chan. B
B
HD or SD SDI Video In
1/2
3/4
Channel B
AES Audio In
Note
: The MDM-5221 provides support for SD only.
Connect to an Automation System (Optional)
All automation systems differ in their array of control connectors and method of interfacing with the Omneon MediaDeck system. The following diagrams provide examples for each MediaDeck Module.
Refer to the documentation supplied with your automation system
for interconnection details.
Continued on the next page
Play
Play
RS-422
Port A
RS-422
Port B
RJ45 Male
to DB-9
Female
Play
Play
Automation System
DB-9 Male
to Male
5400 Series HD/SD MPEG-2/DV Simulcast MediaDeck Module (MDM-5401)
5500 Series HD/SD MPEG-2/DV Playback MediaDeck Module (MDM-5501)
Play
RS-422
Port A
RJ45 Male
to DB-9
Female
Play
Automation System
DB-9 Male
to Male
CAT 5e Ethernet Cable
Connector Detail
Connect to SystemManager
Important
: Use ONLY Omneon-supplied
replacement parts.
Connect to a File Transfer System (Recommended)
8
1
2
3
4
5
6
7
Gigabit Ethernet Switch
Omneon MediaDeck Processor Module
File
Control
3
LAN
File Transfer System
Rear Panel
5
4
NSM 2007, 2007K SystemManager Platform
Rear Panel
Gb 1
Gb 2
2
NIC 1
5400 Series HD/SD MPEG-2/DV Simulcast MediaDeck Module (MDM-5401)
AES Audio Out
Channel A
3/4
RS-422
LTC
IN
OUT
A
For service only
SD SDI Video Out
3/4
1/2
Chan. A
HD SDI Video Out
Channel A
AES Audio Out
1/2
3/4
Unused
Unused
Chan. A
Unused
Unused
Unused