Omer 1146050ROP Скачать руководство пользователя страница 1

Страница: 1 / 20

cod. 1146050ROP

1146050ROP_8016ROP_1 210611 IV

Via Foresto 42 - 31058 SUSEGANA TV ITALY Tel.0438455318 Fax 0438455530 E-mail: [email protected] www.omer.it

80.16 ROP

USE MANUAL and SPARE PARTS

MADE

ITALY

IMPORTANT DO NOT DESTROY !

Read carefully this manual before using the tool and
respect the security norms herewith enclosed.

INTRODUCTION:

The bench-mounted stapler ROP is the optimal solution for fixing blisters, paper or
plastic bags, boxes, displaying cards, etc.

Features:

• Possibility to be easily fixed upon working surface

•Pneumatic system complete with FRL unit & manometer for a correct power

supply

• Pedal activated mode

•Working pressure: 5,5 ÷ 6,5 bar ( 80÷ 95 PSI )

• Top loading

• Magazine capacity: 2 strips

• Applicable sizes: 6 to 16mm

• Easy jam-clearing

• Easily replaceable pneumatic tool units (with units suitable for different fastener

series, i.e. 3G, 64, 80, 50, 65, 40, 4097)

• Possible adjustements:

- Clinching depth
- Front side opening
- Clinching speed
- Fire delay

Содержание 1146050ROP





















Результаты поиска

Содержание 1146050ROP

Отзывы:

Похожие инструкции для 1146050ROP

Бренды по названию

Популярные бренды

Omer 1146050ROP, Руководство пользователя и запасные части

Результаты поиска

Содержание 1146050ROP

Отзывы:

Похожие инструкции для 1146050ROP

Бренды по названию

Популярные бренды