manualshive.com logo in svg

Omega SP-003, Руководство пользователя, Страница: 14 / 38

Поделиться
Скачать
Omega SP-003 Скачать руководство пользователя страница 14

14 | 

M 5 7 4 8

Setting DIO as an Input 

To use a DIO pin as an input, make sure it is set to 

Active Low

 (default) in the 

Output Tab

 in SYNC. 

Then, in the 

Input Tab

, select a 

Type

 from the drop-down which includes DIO. Each DIO pin has an 

internal pull-up, but to save power, the internal pull-up is only active when the unit takes a reading. 

Advanced Scaling Options 

The Omega Link SP-003/SP-004 allows for advanced scaling options on process and pulse inputs only. The 

Advanced Scaling

 checkbox can be selected to expand additional configuration options. A gain and/or 

offset can be applied to the input reading and the displayed unit can be changed. 

To apply a gain or offset to the input, expand the 

Scaling

 menu and ensure that 

Apply Scaling

 is checked. 

There, the gain and offset values can be adjusted. Both positive and negative values may be entered as well 
as decimal numbers. The equation for the scaled input value is given below.

 

𝑰𝒏𝒑𝒖𝒕

𝑺𝒄𝒂𝒍𝒆𝒅

= (𝑰𝒏𝒑𝒖𝒕

𝑹𝒂𝒘

× 𝑮𝒂𝒊𝒏) + 𝑶𝒇𝒇𝒔𝒆𝒕

 

The displayed units can be changed by entering a new value in the 

Unit

 field and clicking 

Apply Settings

. 

This field is limited to a maximum of 4 characters. Note that changing the Unit field does not change the 
base unit type, only the display name. The 

Lock

 checkbox must be selected to use the user-defined Unit 

field. Unchecking the Lock checkbox and clicking 

Apply Settings

 will revert the unit display back to the 

default setting. 

Figure 16: SYNC interface outputs tab 

Figure 17: SYNC interface Digital_IO 

Содержание SP-003







































Отзывы:

Нет отзывов