Page - 5
Page - 16
“
lock
”
button
•
Pressing and releasing the “lock” button locks the doors.
•
Pressing and holding this button for three seconds will first lock, then
activate the Panic feature.
“unlock” button
•
Pressing and releasing the “unlock” button unlocks the doors
•
Pressing and holding this button for three seconds will first unlock,
then activate the Panic feature.
”trunk”
button
•
Pressing the
“
trunk
”
button for two seconds will activate the “2nd
channel” output, for an optional function such as trunk release.
•
Pressing and releasing this button twice, locks or unlocks the system
without confirmation chirps.
”start” button (red)
•
Pressing & releasing the “start” button once will activate the remote start
feature. Pressing it again, during remote start, will stop the engine.
Using The RS-310-EDP System
THE PARKING
LIGHTS WILL FLASH
ONCE
THE DOORS WILL LOCK
To Lock the Vehicle's Doors:
Press & Release the transmitter LOCK button
•
The parking lights flash once to confirm locking, and
optionally, the horn will chirp once. The Status Light
will flash approximately once per second to indicate
that the system is in a LOCKED state.
Feature #2 “Tach Wire” , “Tachless”, or “Data Tach”
Starter Operation
Factory Default Setting:
Tachless (
press
“lock” button to program
)
Options:
Tach Wire (
press
“unlock” button to program
)
Data Tach (
press
“trunk” button to program
)
This feature selects the RS-310-EDP processor’s method of determining the status
of the engine running during remote start operation. As explained in feature 5’s
description, “Tachless” mode has an associated base starter output time duration.
However, if the voltage fluctuation is detectable, the processor adjusts the starter
output time accordingly. When this feature is set for “Tach Wire” operation, the
base starter output increases to a maximum of 3 seconds, but the processor adjusts
the actual starter engagement time accordingly. Connecting and use of the “Tach
Wire” is the most reliable form of engine running information input, and its use is
recommended. Important: Before this feature is programmed, please refer to the
“Violet/White wire” section of the installation manual for proper wiring connec-
tion, and the Tach Learning Procedure. The “Data Tach” setting operates just like
the “Tach Wire” setting except it takes its reading from the D2D data port. Use of
this setting is determined by whether or not this feature is provided by the Databus
Interface module. If so, the Violet/White wire is not needed nor is the Tach Learning
Procedure Required. This feature should only be programmed by the installer.
Feature #3 Gasoline Or Diesel Engine
Factory Default Setting:
Gasoline (
press
“lock” button to program
)
Option:
Diesel
(
press
“unlock” button to program
)
This feature changes the system's timing of the ignition and starter output sequence
for remotely starting vehicles with gas or diesel engines. When set for gasoline, the
starter output will occur 3 seconds after the ignitions turn on. Also, when the system
is in “Tachless” mode, the engine running status will be determined 10 seconds after
cranking. When set for diesel, the starter output will occur 20 seconds after the
ignitions turn on to allow for glow plug warming. Also, when the system is running
in “Tachless” mode, the engine running status will be determined 40 seconds after
cranking. This allows the vehicle battery(s) to recharge properly and show normal
voltage levels due to the heavy drain diesel engines have on the electrical system
during cranking. This feature should only be programmed by the installer.
Feature #4 Satellite Relay Port Green Wire Function:
Factory Default Setting:
Starter
(
press
“lock” button to program
)
Options:
Pulse After Engine Start
(
press
“unlock” button to program
)
Pulse After Engine Stop
(
press
“trunk” button to program
)
Accessory
(
press
“start” button to program
)
THE PARKING
LIGHTS WILL FLASH
TWICE THEN TURN
ON FOR 30 SECONDS
THE DOORS WILL UNLOCK
To Unlock the Vehicle's Doors:
Press & Release the transmitter UNLOCK button
•
The parking lights flash twice then stay on for 30
seconds to confirm unlocking, and optionally the horn
will chirp twice. The Status Light will turn off to indi-
cate that the system is in an UNLOCKED state.
