Page 5-22
Chapter 5 Programming
5.6.5.15.2 Event reset
The Event reset option allows Calculated Points to be programmed to reset upon some external Event
via the optional digital inputs on the rear panel. When programming the Event reset, the Event number
is the digital input number for that external Event (1, 2 or 3). Selecting 0 disables the Event reset.
To set the Event reset function:
From the Reset control menu use the
UP (
↑↑↑↑↑
)
or
DOWN (
↓↓↓↓↓
)
button to highlight
Event reset
and press the
ENTER
button. You will be prompted with “event? X”. Use the
UP (
↑↑↑↑↑
)
or
DOWN (
↓↓↓↓↓
)
button to select the
desired Event input number (0, 1, 2 or 3) and press the
ENTER
button to return to the Reset control menu.
5.6.5.15.3 Reset print
Printing the point reset data to the Alarm/Event data log at the time of the reset, or if enabled, to disk (see
Section 5.7.2) can be toggled On (Yes) or Off (No) for each resettable point using the Reset print option.
To set the Reset print to Yes or No:
From the Reset control menu use the
UP (
↑↑↑↑↑
)
or
DOWN (
↓↓↓↓↓
)
button to highlight
Reset print
and press the
ENTER
button. Press the
YES
or
NO
button to select either
print=YES
(to activate Reset print) or
print=NO
(to disable Reset print) and then press the
ENTER
button to return to the Reset control menu.
5.6.5.16 Time period
The Time period is the time base used to set the duration (time) of the moving window. The point average
is set for this period of time (a maximum 1440 minutes of time is possible) and then the first scan is
dropped off and a new scan is averaged in.
To program the Time period:
From the Point Setup menu use the
UP (
↑↑↑↑↑
)
or
DOWN (
↓↓↓↓↓
)
button to highlight
Time period
and press the
ENTER
button.
You will be prompted with “minutes
→
XXXX
←
”. Use the numeric keypad to enter the
desired time period (up to 1440 minutes, 24 hours) and press the
ENTER
button to return to the Point
Setup menu.
5.6.5.17 Gate control
The Gate control option can be turned On (Yes) or Off (No). If Gate control is turned On, a basepoint must be
established. If Gate control is turned Off, this Point range can be used as a timer for calculations, etc.
To enable or disable Gate control:
From the Point Setup menu use the
UP (
↑↑↑↑↑
)
or
DOWN (
↓↓↓↓↓
)
button to highlight
Gate control
and press the
ENTER
button. Press the
YES
or
NO
button to select either
gate=YES
(to enable Gate control) or
gate=NO
(to disable Gate control) and then press the
ENTER
button. If “gate=NO” is selected, the display
will return to the Point Setup menu. If “gate=YES” is selected, you will be prompted “base pt? X”. Use the
UP (
↑↑↑↑↑
)
or
DOWN (
↓↓↓↓↓
)
button to select the desired point character and then press the
ENTER
button to
return to the Point Setup menu.
5.6.5.18 Flowrate
This function allows different Flowrates to be set which can affect accuracy of the totals.
To set the Flowrate:
From the Point Setup menu use the
UP (
↑↑↑↑↑
)
or
DOWN (
↓↓↓↓↓
)
button to highlight
Flowrate
and press the
ENTER
button. Use the
UP (
↑↑↑↑↑
)
or
DOWN (
↓↓↓↓↓
)
button to select the desired flowrate:
flow= /sec
,
flow= /min
,
flow= /hr
, or
flow= /day
and press the
ENTER
button. Press the
EXIT
button to return to the
Point Setup menu.
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com