background image

OMB-DAQ-TC-RACK User's Guide 

Installing the OMB-DAQ-TC-RACK 

10 

Setting up the OMB-DAQ-TC-RACK for communication across 
networks 

In order to communicate with the OMB-DAQ-TC-RACK from a computer connected to a different network – 
such as over the Internet – you must change the network configuration of the network router.  

In the following procedure, the OMB-DAQ-TC-RACK is installed on the 

host

 LAN, the computer is installed 

on the 

client

 LAN, and it is assumed that you have you have successfully connected the device to a local 

network. 

Caution!

 

This procedure should only be performed by a network administrator or computer professional. 
Incorrect settings can significantly disrupt a network. 

1.

 

Determine the IP address of the device. If the address was assigned by DHCP, it is recommended you 
change it to a static address by setting the default address to the address assigned and setting the device 
network configuration to static. 

2.

 

Configure the firewall/router to forward incoming traffic to the following ports to the IP address assigned 
to the device: 

o

 

UDP:54211 (discovery) 

o

 

TCP:54211 (commands) 

3.

 

On the computer connected to the client LAN, manually enter the WAN address of the host router, and 
specify the ports that were forwarded to connect to the remote OMB-DAQ-TC-RACK. 

Calibrating the hardware 

Factory calibration 

The Omega Engineering Manufacturing Test department performs the initial factory calibration. Return the 
device to Omega Engineering when calibration is required. The recommended calibration interval is one year. 

Field calibration 

The OMB-DAQ-TC-RACK supports field calibration. Calibrate the device using InstaCal whenever the 
ambient temperature changes by more than ±10 °C from the last calibration. 

The following items are required to perform field calibration on a OMB-DAQ-TC-RACK: 

 

a precision voltage source  

 

a voltmeter 

Each ADC (two ADCs per device) is measured at three points and a linear correction is calculated. 

When prompted, enter the voltmeter reading to a precision of three decimal places. 

Omega Engineering strongly recommends that you warm up the OMB-DAQ-TC-RACK for at least 20 minutes 
prior to performing field calibration. 

Restoring factory default network settings 

To reset the network configuration settings to the factory default values, complete the following steps: 

1.

 

Use a ballpoint pen to press and hold in the 

Reset

 button for at least four seconds until both the 

Power

 and 

Activity

 LEDs blink , indicating that the settings have been restored to the factory defaults.  

2.

 

Release the button so the device continues startup with the default settings. If the button is released before 
the two LEDs blink, the settings are not affected and the device starts up normally. 

If InstaCal is open when default settings are restored, click the 

Refresh Boards

 button on the InstaCal toolbar 

to reflect the changes. 

 

Содержание OMB-DAQ-TC-RACK






























Отзывы: