Omega ODW700B, Инструкция по эксплуатации

Страница: 8 / 32

5
Installation Instructions
How to Drain Excess Water from Hoses
If the sink is more than 1000mm higher than the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable container that is
held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks. Ensure that the
water drain hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose. It must be no longer than 4
metres, otherwise the cleaning effect of the dishwasher could be reduced.
Syphon Connection
The waste connection must be at a height less than 1000 mm (maximum) from the bottom of the dish. The
water drain hose should be fixed.
Before Starting the Dishwasher
The following things should be checked before starting the dishwasher:
1. The dishwasher is level and fixed properly.
2. The inlet valve is open.
3. There is a leakage at the connections of the conducts.
4. The wires are tightly connected.
5. The power is switched on.
6. The inlet and drain hoses are knotted.
7. All packing and print materials should be taken out of the dishwasher.
6
Quick Operating Quide
Switch on the appliance. Open the door, press the On/Off button to switch on the appliance.
Fill the detergent dispenser.
Compartment A:
For each wash cycle.
Compartment B:
For programs with pre-wash only.
(Follow the user instructions)
Check the rinse aid level.
Mechanical indicator C.
Electric indicator on control panel (if provided).
Load the baskets.
Scrape off any large food particles. Soften remnants of burnt food in
pans, then load the baskets. Refer to the dishwasher loading
instructions.
Select a program.
Close the door, press the Program button until the selected program
lights up.
Running the dishwasher.
Turn on the water tap and press the Start/Pause Button. The machine
will start working after about 10 seconds.
Changing the program.
1. A running cycle can only be modified if it has been running for a
short time. Otherwise, the detergent may have already been
released and the water already drained. If in this case, the detergent
dispenser must be refilled.
2. Press the Start/Pause button, the machine will be in standby state,
press the program button more than 3 seconds then you can
change the program to the desired cycle setting.
3. Press the Start/Pause Button, the dishwasher will run after 10
seconds.
Adding forgotten dishes to
the dishwasher.
1. Press the Start/Pause Button to stop the washing.
2. Open the door a little.
3. After the spray arms stop working, you can open the door
completely.
4. Add forgotten dishes.
5. Close the door.
6. Press the Start/Pause Button, the dishwasher will run after 10
seconds.
Warning: Open the door carefully as hot steam may be released.
If the appliance is switched
off during a wash cycle.
If the appliance is switched off during a wash cycle, when switched on
again please re-select the washing cycle and operate the dishwasher
according to the original Power-on state.
Switch off the appliance.
When the working cycle is finished, the buzzer of the dishwasher will
sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
If the appliance was under standby mode, it will power off automatically
after 30 minutes without any operation.
Turn off the water tap, unload
the dishes.
Warning: Wait a few minutes (about 15 minutes) before unloading the
dishwasher to avoid scalding, as the dishes and utensils are still hot
and more susceptible to breaking.
Unload the appliance, starting from the lower basket.