3
Installation Instructions
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that
can be positioned either to the right or the left sides to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned for levelling, the height of the dishwasher may be
altered via adjustment of the screwing level of the feet.
Electrical Connection
WARNING
For personal safety:
•
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS
APPLIANCE.
•
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate
power supply. Use the required fuse 10-amp, time delay fuse or circuit breaker recommended and provide
separate circuit serving only this appliance.
Ensure the voltage and frequency of the power supply corresponds to those on the rating plate. Only insert
the plug into an electrical socket which is earthed properly. If the electrical socket to which the appliance
must be connected is not appropriate for the plug, replace the socket, rather than using an adaptor or the
like as they could cause overheating and burns.
Grounding Instructions
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with
a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
4
Installation Instructions
How to Connect the Safety Supply Hose
The appliance must be connected to the water mains using new hose-sets (aqua stop). The old hose-sets
should not be reused.
Water pressure must be between 0.04 MPa and 1 MPa. If the pressure is below the minimum consult our
Service Department for advice.
1.
Pull The safety supply hoses completely out from storage compartment
located at rear of dishwasher.
2.
Tighter the screws of the safety supply hose to the faucet with thread
3/4inch.
3.
Turn water fully on before starting the dishwasher.
About the Safety Supply Hose
The safety supply hose consists of the double walls. The hose's system guarantees its intervention by
blocking the flow of water in case of the supply hose breaking and when the air space between the supply
hose itself and the outer corrugated hose is full of water.
WARNING: A hose that attaches to a sink spray can burst if it is installed on the same water line as the
dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged.
How to Disconnect the Safety Supply Hose
1.
Turn off the water.
2.
Release the water pressure by depressing the pressure release button. This relieves water pressure
and protects you, and the room, from severe splashing.
3.
Unscrew the safety supply hose from the faucet.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened
tightly in place. If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a
risk that the water inlet can get blocked and damage the appliance.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making
sure to avoid bending or crimping it. The top of the hose must be less than 1000mm.
Please connect the drain hose according to point A or B
3
Installation Instructions
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that
can be positioned either to the right or the left sides to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned for levelling, the height of the dishwasher may be
altered via adjustment of the screwing level of the feet.
Electrical Connection
WARNING
For personal safety:
•
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS
APPLIANCE.
•
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate
power supply. Use the required fuse 10-amp, time delay fuse or circuit breaker recommended and provide
separate circuit serving only this appliance.
Ensure the voltage and frequency of the power supply corresponds to those on the rating plate. Only insert
the plug into an electrical socket which is earthed properly. If the electrical socket to which the appliance
must be connected is not appropriate for the plug, replace the socket, rather than using an adaptor or the
like as they could cause overheating and burns.
Grounding Instructions
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with
a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
4
Installation Instructions
How to Connect the Safety Supply Hose
The appliance must be connected to the water mains using new hose-sets (aqua stop). The old hose-sets
should not be reused.
Water pressure must be between 0.04 MPa and 1 MPa. If the pressure is below the minimum consult our
Service Department for advice.
1.
Pull The safety supply hoses completely out from storage compartment
located at rear of dishwasher.
2.
Tighter the screws of the safety supply hose to the faucet with thread
3/4inch.
3.
Turn water fully on before starting the dishwasher.
About the Safety Supply Hose
The safety supply hose consists of the double walls. The hose's system guarantees its intervention by
blocking the flow of water in case of the supply hose breaking and when the air space between the supply
hose itself and the outer corrugated hose is full of water.
WARNING: A hose that attaches to a sink spray can burst if it is installed on the same water line as the
dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged.
How to Disconnect the Safety Supply Hose
1.
Turn off the water.
2.
Release the water pressure by depressing the pressure release button. This relieves water pressure
and protects you, and the room, from severe splashing.
3.
Unscrew the safety supply hose from the faucet.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened
tightly in place. If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a
risk that the water inlet can get blocked and damage the appliance.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making
sure to avoid bending or crimping it. The top of the hose must be less than 1000mm.
Please connect the drain hose according to point A or B
Содержание ODW300XN
Страница 1: ...Instruction Manual Dishwasher ODW300XN...
Страница 28: ...1...