background image

 

36 

LVCN414-SW Appendix 

(continued)

 

Section Six 

  

 

VOLUMETRIC CONFIGURATION 

The  sensor  may  be  configured  in  volumetric  units 
(Gallons  or  Liters)  or  Distance  (Height  of  Liquid) 
units  (inches,  cm,  feet  or  meters).    LVCN414-SW 
will default to Distance (Height of Liquid) with units 
of  Inches.    To  change  units  or  change  from 
Distance  to  Volume,  press  the  Volumetric  Mode 
button as located near the center of the window. 

Distance (Height of Liquid):

  When this is selected, 

the  sensor  will  always  output  a  linear  output 
proportional  to  the  height  of  liquid  (regardless  of  the 
tank  shape).    In  the  two  drawings  below,  the  Sensor 
High is set to 64” and Fill-Height is set to 60”.  If the 
tank is empty, the sensor will output 4mA.  If the level 
is  at  30”,  then  the  sensor  will  output  12mA.    Either 
tank  can  be  configured  with  a  display  from  0”  to  60” 
and the sensor will always output the height of liquid. 

 

Volume:

  When volume is selected, the 4-20 mA output from the sensor will be proportional to the volume of 

the tank, not the height of the tank.  This means that the current output will track the volume of the tank (in 
gallons or liters).  Depending on the shape of the tank, the values may be a linear or non-linear scale.  In the 
same examples below, the sensors are also configured with SH = 64” and FH = 60”.  The current output in a 
linear tank will act as expected with volume increase matching equal changes to level.  However, the current 
output in the Non-Linear tank will reflect the actual changes in volume.  So even though the liquid height 
changes incrementally the same amount, the volume change will adjust throughout the entire span of the tank.  
The advantage of this is that sensor does all the math so you can read tank volume using a simple two-point 
display/controller such as the DataLoop

 LI25 series or DataView

 LI55 series. 

Linear Tank Example 
 

 

Note:

 In the above illustration, 10” of liquid will always 

be equal to 100 gallons of liquid (1” = 10 gallons). 

Non-Linear Tank Example 
 

 

Note:

 In the above illustration, 1” of liquid does not equal 10 

gallons. The 10” at the bottom represents a rise of 62.8 
gallons.  As a change between 10” and 20” represents an 
increase of 109.6 gallons (i.e. 172.4 gallons – 62.8 gallons). 

Содержание LVU500 Series













































Отзывы: