Omega FDT-25W Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 40

Omega FDT-25W Скачать руководство пользователя страница 37

FDT-25W Wall Mounter Ultrasonic Flowmeter

35

the calendar

window M61

Reboot repetitively

Hardware problems

Contact the factory

5.2 Error Code and Counter-Measures

The FDT-25W ultrasonic flow meter will show Error Code in the lower right corner with a single letter
like I, R etc. on menu windows M00, M01, M02, M03, M90 and M08. When any abnormal Error Code
shows, counter-measures should be taken.

Error
code

Correspondent Message
displayed on M08

Causes

Counter-measures

R

System Normal

No error

I

Detect No Signal

(1)No Signals detected
(2)Transducers installed
improperly
(3)Too much fouling
(4)Pipe liners are too thick.
(5)Transducer cords are not
properly connected

(1)Relocate

measuring

location
(2)Clean the spot
(3)Check the cords

J

Hardware Error

Hardware problem

Contact the factory

H

PoorSig Detected

(1)Poor signal detected
(2)Transducers installed
improperly
(3)Too much fouling
(4)The pipe liners are too thick.
(5)Problem with transducers
cords

(1)Relocate measuring place
(2)Clean the spot
(3)Check the cords
(4)Check the coupler

Q

Frequ Output Over

The actual frequency for the
Frequency Output is out of the
range set by the user

Check the value entered at
M66, M67,M68 and M69, and
try to enter a larger value on
M69

F

System RAM Error
Date Time Error
CPU or IRQ Error
ROM Parity Error

(1) Temporary problems with
RAM, RTC

(2) Permanent problems with
hardware

(1) power on again

(2) contact factory

G

Adjusting Gain

Instrument is in the progress of
adjusting the gain for the
signal,

and

the

number

indicates the progressive steps

K

Empty pipe

No liquid inside pipe
Setup error on M29

Relocate where the pipe is
full of liquid
Enter 0 on M29

«
...
35
36
37
38
39
...
»

Содержание FDT-25W









































Отзывы:

Нет отзывов