6) Press the small left transmitter button to turn the feature "off". When done, the
siren will respond with two chirps.
If the Valet Switch is not pressed or if a transmitter signal is not received within a
10 second period, the Programmable Features learning process will automatically
terminate. The 22 Programmable Features are:
1)
Ignition-Activated Anti-Carjacking Protection: Default OFF.
2)
Door-Activated Anti-Carjacking: Default OFF.
3)
Last Door Arming: Default ON.
4)
Doors Lock With Last Door Arming: Default ON.
5)
Current Sensing: Default ON.
6)
Doors Lock At Ignition "On": Default ON.
7)
Unlock Output #1 At Ignition "Off": Default ON.
8)
Unlock Output #2 At Ignition "Off": Default OFF.
9)
Open Door Bypass To Features #6, #7, #8: Default ON.
10)
Lights On 5 / 30 Seconds Upon Disarm: Default 30 Seconds.
11)
Automatic Rearming: Default ON.
12)
2nd Channel Output Disarms System: Default ON.
13)
.8 / 3 Second Doorlock Pulse: Default .8 Second.
14)
Double Unlock Pulse: Default OFF.
Page - 28
Feature #1: Ignition-Activated Anti-Carjacking Protection
(Factory Setting: OFF)
Feature Turned On: After turning the ignition switch "on" and starting the vehicle,
you must press the Valet Switch within 60 seconds. If the Valet Switch is not pressed
the security system will begin chirping the siren 53 seconds after the ignition was
turned "on". These chirps are to remind you that Anti-Carjacking is about to engage;
pressing the Valet Switch during the chirps will cancel the Anti-Carjacking feature.
The chirps will last for 7 seconds, after which time the siren will sound continuously
and the parking lights will begin flashing to attract attention to the vehicle.
15)
3 / 45 Second Arming Delay: Default 3 Seconds.
16)
Confirmation Chirp: Default ON.
17)
30 / 60 Second Activated Alarm Cycle: Default 60 Seconds.
18)
Pulsed Horn / Steady Siren Output: Default Steady Siren.
19)
Loud / Soft Pulsed Horn Chirps: Default Loud.
20)
Total Closure Lock Output: Default OFF.
21)
Remote-Activated Anti-Carjacking Protection: Default OFF.
22)
One / Two Button Arming / Disarming: Default One Button.
Programmable Features
Page - 29
Thirty seconds after the siren and parking lights engage, or if the ignition is turned
"off", the starter interrupt will engage. Once the Anti-Carjack is engaged, the only
way to disengage it is to turn the ignition "off", then back "on" again, and then press
the Valet Switch within 5 seconds. Altogether, there are three Anti-Carjacking
Programmable Features, which may be programmed independently.
Feature #2: Door-Activated Anti-Carjacking Protection
(Factory Setting: OFF)
Feature Turned On: This feature operates the same as the Anti-Carjacking feature
described above, except that opening a door while the ignition is "on" will initiate
the 60 second Anti-Carjacking cycle.
Feature #3: Last Door Arming
(Factory Setting: ON)
Feature Turned On: The security system will arm itself automatically when the
vehicle's last door is closed. At the moment the last door is closed the siren will chirp
the exterior lights will flash once, and the Status LED will flash fast. Thirty seconds
later the siren will chirp once again, the lights will flash, and the Status LED will
flash slowly, indicating that the security system is fully armed. If feature #4 is
selected, the doors will also lock at this time. If the instant trigger is grounded at any
time during the thirty second countdown (Example: opening the trunk), the
Page - 30
Automatic Last Door Arming feature will be interrupted. When the instant trigger
becomes ungrounded, the security system will become fully armed thirty seconds
later. All of the doors and the trunk must have the proper connection of the control
module's wiring. This feature allows unhurried passenger exit and trunk access, as
the Last Door Arming process does not start until the last door or trunk is closed,
and opening any door or the trunk will interrupt the process. You can still actively
arm the security system with the transmitter at any time.
Feature #4 Doors Lock With Last Door Arming (Factory Setting: ON)
Feature Turned On: When the security system passively arms from the Last Door
Arming feature, the doors will also lock if an optional doorlock interface was added.
This will occur when the system becomes fully armed 30 seconds after closing the
last door. Feature #3 must be on in order for this feature to operate.
Feature #5: Current Sensing (Factory Setting: ON)
Feature Turned On: When the security system is armed, current sensing can detect
a positive current draw from the vehicle's battery. (Example: the dome light comes
on when a door is opened or the brake lights come on when the brake pedal is
pressed). With this feature on, the security system will trigger if a current draw is
detected.
Page - 31
