background image

page 4

Caution:

  Failure to fully open terminal jaws before removing wire may permanently damage instrument.

Wiring Procedure

1.

Remove 0.5 - 0.625 in. (13-16 mm) of insulation from wire end.

2.

Press the orange terminal lever downward with a small screwdriver to open terminal jaws.

3.

Insert exposed (non-insulated) wire end in terminal hole until it bottoms out.

4.

Release orange terminal lever to secure wire in place.  Gently pull on each wire to ensure a good connection.

Wiring Removal Procedure

1.

Press the orange terminal lever downward with a small screwdriver to open terminal jaws.

2.

When fully open, remove wire from terminal.

2

1

Wiring Tips:

Do not route sensor cable in conduit containing AC power
wiring.  Electrical noise may interfere with sensor signal.

Routing sensor cable in grounded metal conduit will help
prevent electrical noise and mechanical damage.

Seal cable entry points to prevent moisture damage.

Only one wire should be inserted into a terminal.  Splice
double wires outside the terminal.

Sensor cable may not be extended over 100 ft.

Sensor Selection

Select the sensor with a range closest to your process minimum and
maximum values.

•   CDCE-90-001 (0.01 cell):  0.055 to 100 

µ

S (10 k

 to 18 M

)

Use the CDCE-90-001 for all resistivity requirements

CDCE-90-01 (0.1 cell):

1 to 1000 

µ

S

CDCE-90-1 (1.0 cell):

10 to 10,000 

µ

S

CDCE-90-10 (10.0 cell):

100 to 200,000 

µ

S

CDCE-90-20 (20.0 cell):

200 to 400,000 

µ

S

(18 MΩ)

(10 kΩ)

CDCE-90-001

CDCE-90-20

Conductivity Range (µS)

CDCE-90 Series Sensor Ranges

Sensor Models

Ultra-

Pure

Rinse

Pure

CDCE-90-1

CDCE-90-10

CDCE-90-01

0.055

1

10 100 200

1,000

10,000

200,000

400,000

CDTX-90

≤ 100 ft. (30 m)

Conductivity/Resistivity

62.50 uS/cm

25.0

°

C

ENTER

14
13
12
11

Shield (Sensor Gnd)
Black (Iso Gnd)
White (Temp In)
Red (Signal In)

CDTX-90-2 Terminals

CDCE-90 Series Standard and Certified Cells

14
13
12
11

Shield (Sensor Gnd)
Black (Iso Gnd)
White (Temp In)
Red (Signal In)

CDTX-90-3 Terminals

10

9
8
7

Shield (Sensor Gnd)
Black (Iso Gnd)
White (Temp In)
Red (Signal In)

CDTX-90-1 Terminals

3.1 Sensor Connections

3.

Electrical Connections

Содержание CDTX-90 Series





















Отзывы: